avformat/dashenc: add a PlaybackRate element

[ffmpeg] / doc / muxers.texi

@chapter Muxers
@c man begin MUXERS

Muxers are configured elements in FFmpeg which allow writing
multimedia streams to a particular type of file.

When you configure your FFmpeg build, all the supported muxers
are enabled by default. You can list all available muxers using the
configure option @code{--list-muxers}.

You can disable all the muxers with the configure option
@code{--disable-muxers} and selectively enable / disable single muxers
with the options @code{--enable-muxer=@var{MUXER}} /
@code{--disable-muxer=@var{MUXER}}.

The option @code{-muxers} of the ff* tools will display the list of
enabled muxers. Use @code{-formats} to view a combined list of
enabled demuxers and muxers.

A description of some of the currently available muxers follows.

@anchor{aiff}
@section aiff

Audio Interchange File Format muxer.

@subsection Options

It accepts the following options:

@table @option
@item write_id3v2
Enable ID3v2 tags writing when set to 1. Default is 0 (disabled).

@item id3v2_version
Select ID3v2 version to write. Currently only version 3 and 4 (aka.
ID3v2.3 and ID3v2.4) are supported. The default is version 4.

@end table

@anchor{asf}
@section asf

Advanced Systems Format muxer.

Note that Windows Media Audio (wma) and Windows Media Video (wmv) use this
muxer too.

@subsection Options

It accepts the following options:

@table @option
@item packet_size
Set the muxer packet size. By tuning this setting you may reduce data
fragmentation or muxer overhead depending on your source. Default value is
3200, minimum is 100, maximum is 64k.

@end table

@anchor{avi}
@section avi

Audio Video Interleaved muxer.

@subsection Options

It accepts the following options:

@table @option
@item reserve_index_space
Reserve the specified amount of bytes for the OpenDML master index of each
stream within the file header. By default additional master indexes are
embedded within the data packets if there is no space left in the first master
index and are linked together as a chain of indexes. This index structure can
cause problems for some use cases, e.g. third-party software strictly relying
on the OpenDML index specification or when file seeking is slow. Reserving
enough index space in the file header avoids these problems.

The required index space depends on the output file size and should be about 16
bytes per gigabyte. When this option is omitted or set to zero the necessary
index space is guessed.

@item write_channel_mask
Write the channel layout mask into the audio stream header.

This option is enabled by default. Disabling the channel mask can be useful in
specific scenarios, e.g. when merging multiple audio streams into one for
compatibility with software that only supports a single audio stream in AVI
(see @ref{amerge,,the "amerge" section in the ffmpeg-filters manual,ffmpeg-filters}).

@end table

@anchor{chromaprint}
@section chromaprint

Chromaprint fingerprinter.

This muxer feeds audio data to the Chromaprint library,
which generates a fingerprint for the provided audio data. See @url{https://acoustid.org/chromaprint}

It takes a single signed native-endian 16-bit raw audio stream of at most 2 channels.

@subsection Options

@table @option
@item silence_threshold
Threshold for detecting silence. Range is from -1 to 32767, where -1 disables
silence detection. Silence detection can only be used with version 3 of the
algorithm.
Silence detection must be disabled for use with the AcoustID service. Default is -1.

@item algorithm
Version of algorithm to fingerprint with. Range is 0 to 4.
Version 3 enables silence detection. Default is 1.

@item fp_format
Format to output the fingerprint as. Accepts the following options:
@table @samp
@item raw
Binary raw fingerprint

@item compressed
Binary compressed fingerprint

@item base64
Base64 compressed fingerprint @emph{(default)}

@end table

@end table

@anchor{crc}
@section crc

CRC (Cyclic Redundancy Check) testing format.

This muxer computes and prints the Adler-32 CRC of all the input audio
and video frames. By default audio frames are converted to signed
16-bit raw audio and video frames to raw video before computing the
CRC.

The output of the muxer consists of a single line of the form:
CRC=0x@var{CRC}, where @var{CRC} is a hexadecimal number 0-padded to
8 digits containing the CRC for all the decoded input frames.

See also the @ref{framecrc} muxer.

@subsection Examples

For example to compute the CRC of the input, and store it in the file
@file{out.crc}:
@example
ffmpeg -i INPUT -f crc out.crc
@end example

You can print the CRC to stdout with the command:
@example
ffmpeg -i INPUT -f crc -
@end example

You can select the output format of each frame with @command{ffmpeg} by
specifying the audio and video codec and format. For example to
compute the CRC of the input audio converted to PCM unsigned 8-bit
and the input video converted to MPEG-2 video, use the command:
@example
ffmpeg -i INPUT -c:a pcm_u8 -c:v mpeg2video -f crc -
@end example

@section flv

Adobe Flash Video Format muxer.

This muxer accepts the following options:

@table @option

@item flvflags @var{flags}
Possible values:

@table @samp

@item aac_seq_header_detect
Place AAC sequence header based on audio stream data.

@item no_sequence_end
Disable sequence end tag.

@item no_metadata
Disable metadata tag.

@item no_duration_filesize
Disable duration and filesize in metadata when they are equal to zero
at the end of stream. (Be used to non-seekable living stream).

@item add_keyframe_index
Used to facilitate seeking; particularly for HTTP pseudo streaming.
@end table
@end table

@anchor{dash}
@section dash

Dynamic Adaptive Streaming over HTTP (DASH) muxer that creates segments
and manifest files according to the MPEG-DASH standard ISO/IEC 23009-1:2014.

For more information see:

@itemize @bullet
@item
ISO DASH Specification: @url{http://standards.iso.org/ittf/PubliclyAvailableStandards/c065274_ISO_IEC_23009-1_2014.zip}
@item
WebM DASH Specification: @url{https://sites.google.com/a/webmproject.org/wiki/adaptive-streaming/webm-dash-specification}
@end itemize

It creates a MPD manifest file and segment files for each stream.

The segment filename might contain pre-defined identifiers used with SegmentTemplate
as defined in section 5.3.9.4.4 of the standard. Available identifiers are "$RepresentationID$",
"$Number$", "$Bandwidth$" and "$Time$".
In addition to the standard identifiers, an ffmpeg-specific "$ext$" identifier is also supported.
When specified ffmpeg will replace $ext$ in the file name with muxing format's extensions such as mp4, webm etc.,

@example
ffmpeg -re -i <input> -map 0 -map 0 -c:a libfdk_aac -c:v libx264 \
-b:v:0 800k -b:v:1 300k -s:v:1 320x170 -profile:v:1 baseline \
-profile:v:0 main -bf 1 -keyint_min 120 -g 120 -sc_threshold 0 \
-b_strategy 0 -ar:a:1 22050 -use_timeline 1 -use_template 1 \
-window_size 5 -adaptation_sets "id=0,streams=v id=1,streams=a" \
-f dash /path/to/out.mpd
@end example

@table @option
@item min_seg_duration @var{microseconds}
This is a deprecated option to set the segment length in microseconds, use @var{seg_duration} instead.
@item seg_duration @var{duration}
Set the segment length in seconds (fractional value can be set). The value is
treated as average segment duration when @var{use_template} is enabled and
@item frag_duration @var{duration}
Set the length in seconds of fragments within segments (fractional value can be set).
@item frag_type @var{type}
Set the type of interval for fragmentation.
@item window_size @var{size}
Set the maximum number of segments kept in the manifest.
@item extra_window_size @var{size}
Set the maximum number of segments kept outside of the manifest before removing from disk.
@item remove_at_exit @var{remove}
Enable (1) or disable (0) removal of all segments when finished.
@item use_template @var{template}
Enable (1) or disable (0) use of SegmentTemplate instead of SegmentList.
@item use_timeline @var{timeline}
Enable (1) or disable (0) use of SegmentTimeline in SegmentTemplate.
@item single_file @var{single_file}
Enable (1) or disable (0) storing all segments in one file, accessed using byte ranges.
@item single_file_name @var{file_name}
DASH-templated name to be used for baseURL. Implies @var{single_file} set to "1". In the template, "$ext$" is replaced with the file name extension specific for the segment format.
@item init_seg_name @var{init_name}
DASH-templated name to used for the initialization segment. Default is "init-stream$RepresentationID$.$ext$". "$ext$" is replaced with the file name extension specific for the segment format.
@item media_seg_name @var{segment_name}
DASH-templated name to used for the media segments. Default is "chunk-stream$RepresentationID$-$Number%05d$.$ext$". "$ext$" is replaced with the file name extension specific for the segment format.
@item utc_timing_url @var{utc_url}
URL of the page that will return the UTC timestamp in ISO format. Example: "https://time.akamai.com/?iso"
@item method @var{method}
Use the given HTTP method to create output files. Generally set to PUT or POST.
@item http_user_agent @var{user_agent}
Override User-Agent field in HTTP header. Applicable only for HTTP output.
@item http_persistent @var{http_persistent}
Use persistent HTTP connections. Applicable only for HTTP output.
@item hls_playlist @var{hls_playlist}
Generate HLS playlist files as well. The master playlist is generated with the filename master.m3u8.
One media playlist file is generated for each stream with filenames media_0.m3u8, media_1.m3u8, etc.
@item streaming @var{streaming}
Enable (1) or disable (0) chunk streaming mode of output. In chunk streaming
mode, each frame will be a moof fragment which forms a chunk.
@item adaptation_sets @var{adaptation_sets}
Assign streams to AdaptationSets. Syntax is "id=x,streams=a,b,c id=y,streams=d,e" with x and y being the IDs
of the adaptation sets and a,b,c,d and e are the indices of the mapped streams.

To map all video (or audio) streams to an AdaptationSet, "v" (or "a") can be used as stream identifier instead of IDs.

When no assignment is defined, this defaults to an AdaptationSet for each stream.

Optional syntax is "id=x,seg_duration=x,frag_duration=x,frag_type=type,descriptor=descriptor_string,streams=a,b,c id=y,seg_duration=y,frag_type=type,streams=d,e" and so on,
descriptor is useful to the scheme defined by ISO/IEC 23009-1:2014/Amd.2:2015.
For example, -adaptation_sets "id=0,descriptor=<SupplementalProperty schemeIdUri=\"urn:mpeg:dash:srd:2014\" value=\"0,0,0,1,1,2,2\"/>,streams=v".
Please note that descriptor string should be a self-closing xml tag.
seg_duration, frag_duration and frag_type override the global option values for each adaptation set.
For example, -adaptation_sets "id=0,seg_duration=2,frag_duration=1,frag_type=duration,streams=v id=1,seg_duration=2,frag_type=none,streams=a"
type_id marks an adaptation set as containing streams meant to be used for Trick Mode for the referenced adaptation set.
For example, -adaptation_sets "id=0,seg_duration=2,frag_type=none,streams=0 id=1,seg_duration=10,frag_type=none,trick_id=0,streams=1"
@item timeout @var{timeout}
Set timeout for socket I/O operations. Applicable only for HTTP output.
@item index_correction @var{index_correction}
Enable (1) or Disable (0) segment index correction logic. Applicable only when
@var{use_template} is enabled and @var{use_timeline} is disabled.

When enabled, the logic monitors the flow of segment indexes. If a streams's
segment index value is not at the expected real time position, then the logic
corrects that index value.

Typically this logic is needed in live streaming use cases. The network bandwidth
fluctuations are common during long run streaming. Each fluctuation can cause
the segment indexes fall behind the expected real time position.
@item format_options @var{options_list}
Set container format (mp4/webm) options using a @code{:} separated list of
key=value parameters. Values containing @code{:} special characters must be
escaped.

@item global_sidx @var{global_sidx}
Write global SIDX atom. Applicable only for single file, mp4 output, non-streaming mode.

@item dash_segment_type @var{dash_segment_type}
Possible values:
@table @option
@item auto
If this flag is set, the dash segment files format will be selected based on the stream codec. This is the default mode.

@item mp4
If this flag is set, the dash segment files will be in in ISOBMFF format.

@item webm
If this flag is set, the dash segment files will be in in WebM format.
@end table

@item ignore_io_errors @var{ignore_io_errors}
Ignore IO errors during open and write. Useful for long-duration runs with network output.

@item lhls @var{lhls}
Enable Low-latency HLS(LHLS). Adds #EXT-X-PREFETCH tag with current segment's URI.
Apple doesn't have an official spec for LHLS. Meanwhile hls.js player folks are
trying to standardize a open LHLS spec. The draft spec is available in https://github.com/video-dev/hlsjs-rfcs/blob/lhls-spec/proposals/0001-lhls.md
This option will also try to comply with the above open spec, till Apple's spec officially supports it.
Applicable only when @var{streaming} and @var{hls_playlist} options are enabled.
This is an experimental feature.

@item ldash @var{ldash}
Enable Low-latency Dash by constraining the presence and values of some elements.

@item master_m3u8_publish_rate @var{master_m3u8_publish_rate}
Publish master playlist repeatedly every after specified number of segment intervals.

@item write_prft @var{write_prft}
Write Producer Reference Time elements on supported streams. This also enables writing
prft boxes in the underlying muxer. Applicable only when the @var{utc_url} option is enabled.
It's set to auto by default, in which case the muxer will attempt to enable it only in modes
that require it.

@item mpd_profile @var{mpd_profile}
Set one or more manifest profiles.

@item http_opts @var{http_opts}
A :-separated list of key=value options to pass to the underlying HTTP
protocol. Applicable only for HTTP output.

@item target_latency @var{target_latency}
Set an intended target latency in seconds (fractional value can be set) for serving. Applicable only when @var{streaming} and @var{write_prft} options are enabled.
This is an informative fields clients can use to measure the latency of the service.

@item min_playback_rate @var{min_playback_rate}
Set the minimum playback rate indicated as appropriate for the purposes of automatically
adjusting playback latency and buffer occupancy during normal playback by clients.

@item max_playback_rate @var{max_playback_rate}
Set the maximum playback rate indicated as appropriate for the purposes of automatically
adjusting playback latency and buffer occupancy during normal playback by clients.

@end table

@anchor{framecrc}
@section framecrc

Per-packet CRC (Cyclic Redundancy Check) testing format.

This muxer computes and prints the Adler-32 CRC for each audio
and video packet. By default audio frames are converted to signed
16-bit raw audio and video frames to raw video before computing the
CRC.

The output of the muxer consists of a line for each audio and video
packet of the form:
@example
@var{stream_index}, @var{packet_dts}, @var{packet_pts}, @var{packet_duration}, @var{packet_size}, 0x@var{CRC}
@end example

@var{CRC} is a hexadecimal number 0-padded to 8 digits containing the
CRC of the packet.

@subsection Examples

For example to compute the CRC of the audio and video frames in
@file{INPUT}, converted to raw audio and video packets, and store it
in the file @file{out.crc}:
@example
ffmpeg -i INPUT -f framecrc out.crc
@end example

To print the information to stdout, use the command:
@example
ffmpeg -i INPUT -f framecrc -
@end example

With @command{ffmpeg}, you can select the output format to which the
audio and video frames are encoded before computing the CRC for each
packet by specifying the audio and video codec. For example, to
compute the CRC of each decoded input audio frame converted to PCM
unsigned 8-bit and of each decoded input video frame converted to
MPEG-2 video, use the command:
@example
ffmpeg -i INPUT -c:a pcm_u8 -c:v mpeg2video -f framecrc -
@end example

See also the @ref{crc} muxer.

@anchor{framehash}
@section framehash

Per-packet hash testing format.

This muxer computes and prints a cryptographic hash for each audio
and video packet. This can be used for packet-by-packet equality
checks without having to individually do a binary comparison on each.

By default audio frames are converted to signed 16-bit raw audio and
video frames to raw video before computing the hash, but the output
of explicit conversions to other codecs can also be used. It uses the
SHA-256 cryptographic hash function by default, but supports several
other algorithms.

The output of the muxer consists of a line for each audio and video
packet of the form:
@example
@var{stream_index}, @var{packet_dts}, @var{packet_pts}, @var{packet_duration}, @var{packet_size}, @var{hash}
@end example

@var{hash} is a hexadecimal number representing the computed hash
for the packet.

@table @option
@item hash @var{algorithm}
Use the cryptographic hash function specified by the string @var{algorithm}.
Supported values include @code{MD5}, @code{murmur3}, @code{RIPEMD128},
@code{RIPEMD160}, @code{RIPEMD256}, @code{RIPEMD320}, @code{SHA160},
@code{SHA224}, @code{SHA256} (default), @code{SHA512/224}, @code{SHA512/256},
@code{SHA384}, @code{SHA512}, @code{CRC32} and @code{adler32}.

@end table

@subsection Examples

To compute the SHA-256 hash of the audio and video frames in @file{INPUT},
converted to raw audio and video packets, and store it in the file
@file{out.sha256}:
@example
ffmpeg -i INPUT -f framehash out.sha256
@end example

To print the information to stdout, using the MD5 hash function, use
the command:
@example
ffmpeg -i INPUT -f framehash -hash md5 -
@end example

See also the @ref{hash} muxer.

@anchor{framemd5}
@section framemd5

Per-packet MD5 testing format.

This is a variant of the @ref{framehash} muxer. Unlike that muxer,
it defaults to using the MD5 hash function.

@subsection Examples

To compute the MD5 hash of the audio and video frames in @file{INPUT},
converted to raw audio and video packets, and store it in the file
@file{out.md5}:
@example
ffmpeg -i INPUT -f framemd5 out.md5
@end example

To print the information to stdout, use the command:
@example
ffmpeg -i INPUT -f framemd5 -
@end example

See also the @ref{framehash} and @ref{md5} muxers.

@anchor{gif}
@section gif

Animated GIF muxer.

It accepts the following options:

@table @option
@item loop
Set the number of times to loop the output. Use @code{-1} for no loop, @code{0}
for looping indefinitely (default).

@item final_delay
Force the delay (expressed in centiseconds) after the last frame. Each frame
ends with a delay until the next frame. The default is @code{-1}, which is a
special value to tell the muxer to re-use the previous delay. In case of a
loop, you might want to customize this value to mark a pause for instance.
@end table

For example, to encode a gif looping 10 times, with a 5 seconds delay between
the loops:
@example
ffmpeg -i INPUT -loop 10 -final_delay 500 out.gif
@end example

Note 1: if you wish to extract the frames into separate GIF files, you need to
force the @ref{image2} muxer:
@example
ffmpeg -i INPUT -c:v gif -f image2 "out%d.gif"
@end example

Note 2: the GIF format has a very large time base: the delay between two frames
can therefore not be smaller than one centi second.

@anchor{hash}
@section hash

Hash testing format.

This muxer computes and prints a cryptographic hash of all the input
audio and video frames. This can be used for equality checks without
having to do a complete binary comparison.

By default audio frames are converted to signed 16-bit raw audio and
video frames to raw video before computing the hash, but the output
of explicit conversions to other codecs can also be used. Timestamps
are ignored. It uses the SHA-256 cryptographic hash function by default,
but supports several other algorithms.

The output of the muxer consists of a single line of the form:
@var{algo}=@var{hash}, where @var{algo} is a short string representing
the hash function used, and @var{hash} is a hexadecimal number
representing the computed hash.

@table @option
@item hash @var{algorithm}
Use the cryptographic hash function specified by the string @var{algorithm}.
Supported values include @code{MD5}, @code{murmur3}, @code{RIPEMD128},
@code{RIPEMD160}, @code{RIPEMD256}, @code{RIPEMD320}, @code{SHA160},
@code{SHA224}, @code{SHA256} (default), @code{SHA512/224}, @code{SHA512/256},
@code{SHA384}, @code{SHA512}, @code{CRC32} and @code{adler32}.

@end table

@subsection Examples

To compute the SHA-256 hash of the input converted to raw audio and
video, and store it in the file @file{out.sha256}:
@example
ffmpeg -i INPUT -f hash out.sha256
@end example

To print an MD5 hash to stdout use the command:
@example
ffmpeg -i INPUT -f hash -hash md5 -
@end example

See also the @ref{framehash} muxer.

@anchor{hls}
@section hls

Apple HTTP Live Streaming muxer that segments MPEG-TS according to
the HTTP Live Streaming (HLS) specification.

It creates a playlist file, and one or more segment files. The output filename
specifies the playlist filename.

By default, the muxer creates a file for each segment produced. These files
have the same name as the playlist, followed by a sequential number and a
.ts extension.

Make sure to require a closed GOP when encoding and to set the GOP
size to fit your segment time constraint.

For example, to convert an input file with @command{ffmpeg}:
@example
ffmpeg -i in.mkv -c:v h264 -flags +cgop -g 30 -hls_time 1 out.m3u8
@end example
This example will produce the playlist, @file{out.m3u8}, and segment files:
@file{out0.ts}, @file{out1.ts}, @file{out2.ts}, etc.

See also the @ref{segment} muxer, which provides a more generic and
flexible implementation of a segmenter, and can be used to perform HLS
segmentation.

@subsection Options

This muxer supports the following options:

@table @option
@item hls_init_time @var{seconds}
Set the initial target segment length in seconds. Default value is @var{0}.
Segment will be cut on the next key frame after this time has passed on the first m3u8 list.
After the initial playlist is filled @command{ffmpeg} will cut segments
at duration equal to @code{hls_time}

@item hls_time @var{seconds}
Set the target segment length in seconds. Default value is 2.
Segment will be cut on the next key frame after this time has passed.

@item hls_list_size @var{size}
Set the maximum number of playlist entries. If set to 0 the list file
will contain all the segments. Default value is 5.

@item hls_delete_threshold @var{size}
Set the number of unreferenced segments to keep on disk before @code{hls_flags delete_segments}
deletes them. Increase this to allow continue clients to download segments which
were recently referenced in the playlist. Default value is 1, meaning segments older than
@code{hls_list_size+1} will be deleted.

@item hls_ts_options @var{options_list}
Set output format options using a :-separated list of key=value
parameters. Values containing @code{:} special characters must be
escaped.

@item hls_wrap @var{wrap}
This is a deprecated option, you can use @code{hls_list_size}
and @code{hls_flags delete_segments} instead it

This option is useful to avoid to fill the disk with many segment
files, and limits the maximum number of segment files written to disk
to @var{wrap}.


@item hls_start_number_source
Start the playlist sequence number (@code{#EXT-X-MEDIA-SEQUENCE}) according to the specified source.
Unless @code{hls_flags single_file} is set, it also specifies source of starting sequence numbers of
segment and subtitle filenames. In any case, if @code{hls_flags append_list}
is set and read playlist sequence number is greater than the specified start sequence number,
then that value will be used as start value.

It accepts the following values:

@table @option

@item generic (default)
Set the starting sequence numbers according to @var{start_number} option value.

@item epoch
The start number will be the seconds since epoch (1970-01-01 00:00:00)

@item datetime
The start number will be based on the current date/time as YYYYmmddHHMMSS. e.g. 20161231235759.

@end table

@item start_number @var{number}
Start the playlist sequence number (@code{#EXT-X-MEDIA-SEQUENCE}) from the specified @var{number}
when @var{hls_start_number_source} value is @var{generic}. (This is the default case.)
Unless @code{hls_flags single_file} is set, it also specifies starting sequence numbers of segment and subtitle filenames.
Default value is 0.

@item hls_allow_cache @var{allowcache}
Explicitly set whether the client MAY (1) or MUST NOT (0) cache media segments.

@item hls_base_url @var{baseurl}
Append @var{baseurl} to every entry in the playlist.
Useful to generate playlists with absolute paths.

Note that the playlist sequence number must be unique for each segment
and it is not to be confused with the segment filename sequence number
which can be cyclic, for example if the @option{wrap} option is
specified.

@item hls_segment_filename @var{filename}
Set the segment filename. Unless @code{hls_flags single_file} is set,
@var{filename} is used as a string format with the segment number:
@example
ffmpeg -i in.nut -hls_segment_filename 'file%03d.ts' out.m3u8
@end example
This example will produce the playlist, @file{out.m3u8}, and segment files:
@file{file000.ts}, @file{file001.ts}, @file{file002.ts}, etc.

@var{filename} may contain full path or relative path specification,
but only the file name part without any path info will be contained in the m3u8 segment list.
Should a relative path be specified, the path of the created segment
files will be relative to the current working directory.
When strftime_mkdir is set, the whole expanded value of @var{filename} will be written into the m3u8 segment list.

When @code{var_stream_map} is set with two or more variant streams, the
@var{filename} pattern must contain the string "%v", this string specifies
the position of variant stream index in the generated segment file names.
@example
ffmpeg -i in.ts -b:v:0 1000k -b:v:1 256k -b:a:0 64k -b:a:1 32k \
  -map 0:v -map 0:a -map 0:v -map 0:a -f hls -var_stream_map "v:0,a:0 v:1,a:1" \
  -hls_segment_filename 'file_%v_%03d.ts' out_%v.m3u8
@end example
This example will produce the playlists segment file sets:
@file{file_0_000.ts}, @file{file_0_001.ts}, @file{file_0_002.ts}, etc. and
@file{file_1_000.ts}, @file{file_1_001.ts}, @file{file_1_002.ts}, etc.

The string "%v" may be present in the filename or in the last directory name
containing the file, but only in one of them. (Additionally, %v may appear multiple times in the last
sub-directory or filename.) If the string %v is present in the directory name, then
sub-directories are created after expanding the directory name pattern. This
enables creation of segments corresponding to different variant streams in
subdirectories.
@example
ffmpeg -i in.ts -b:v:0 1000k -b:v:1 256k -b:a:0 64k -b:a:1 32k \
  -map 0:v -map 0:a -map 0:v -map 0:a -f hls -var_stream_map "v:0,a:0 v:1,a:1" \
  -hls_segment_filename 'vs%v/file_%03d.ts' vs%v/out.m3u8
@end example
This example will produce the playlists segment file sets:
@file{vs0/file_000.ts}, @file{vs0/file_001.ts}, @file{vs0/file_002.ts}, etc. and
@file{vs1/file_000.ts}, @file{vs1/file_001.ts}, @file{vs1/file_002.ts}, etc.

@item use_localtime
Same as strftime option, will be deprecated.

@item strftime
Use strftime() on @var{filename} to expand the segment filename with localtime.
The segment number is also available in this mode, but to use it, you need to specify second_level_segment_index
hls_flag and %%d will be the specifier.
@example
ffmpeg -i in.nut -strftime 1 -hls_segment_filename 'file-%Y%m%d-%s.ts' out.m3u8
@end example
This example will produce the playlist, @file{out.m3u8}, and segment files:
@file{file-20160215-1455569023.ts}, @file{file-20160215-1455569024.ts}, etc.
Note: On some systems/environments, the @code{%s} specifier is not available. See
  @code{strftime()} documentation.
@example
ffmpeg -i in.nut -strftime 1 -hls_flags second_level_segment_index -hls_segment_filename 'file-%Y%m%d-%%04d.ts' out.m3u8
@end example
This example will produce the playlist, @file{out.m3u8}, and segment files:
@file{file-20160215-0001.ts}, @file{file-20160215-0002.ts}, etc.

@item use_localtime_mkdir
Same as strftime_mkdir option, will be deprecated .

@item strftime_mkdir
Used together with -strftime_mkdir, it will create all subdirectories which
is expanded in @var{filename}.
@example
ffmpeg -i in.nut -strftime 1 -strftime_mkdir 1 -hls_segment_filename '%Y%m%d/file-%Y%m%d-%s.ts' out.m3u8
@end example
This example will create a directory 201560215 (if it does not exist), and then
produce the playlist, @file{out.m3u8}, and segment files:
@file{20160215/file-20160215-1455569023.ts}, @file{20160215/file-20160215-1455569024.ts}, etc.

@example
ffmpeg -i in.nut -strftime 1 -strftime_mkdir 1 -hls_segment_filename '%Y/%m/%d/file-%Y%m%d-%s.ts' out.m3u8
@end example
This example will create a directory hierarchy 2016/02/15 (if any of them do not exist), and then
produce the playlist, @file{out.m3u8}, and segment files:
@file{2016/02/15/file-20160215-1455569023.ts}, @file{2016/02/15/file-20160215-1455569024.ts}, etc.


@item hls_key_info_file @var{key_info_file}
Use the information in @var{key_info_file} for segment encryption. The first
line of @var{key_info_file} specifies the key URI written to the playlist. The
key URL is used to access the encryption key during playback. The second line
specifies the path to the key file used to obtain the key during the encryption
process. The key file is read as a single packed array of 16 octets in binary
format. The optional third line specifies the initialization vector (IV) as a
hexadecimal string to be used instead of the segment sequence number (default)
for encryption. Changes to @var{key_info_file} will result in segment
encryption with the new key/IV and an entry in the playlist for the new key
URI/IV if @code{hls_flags periodic_rekey} is enabled.

Key info file format:
@example
@var{key URI}
@var{key file path}
@var{IV} (optional)
@end example

Example key URIs:
@example
http://server/file.key
/path/to/file.key
file.key
@end example

Example key file paths:
@example
file.key
/path/to/file.key
@end example

Example IV:
@example
0123456789ABCDEF0123456789ABCDEF
@end example

Key info file example:
@example
http://server/file.key
/path/to/file.key
0123456789ABCDEF0123456789ABCDEF
@end example

Example shell script:
@example
#!/bin/sh
BASE_URL=$@{1:-'.'@}
openssl rand 16 > file.key
echo $BASE_URL/file.key > file.keyinfo
echo file.key >> file.keyinfo
echo $(openssl rand -hex 16) >> file.keyinfo
ffmpeg -f lavfi -re -i testsrc -c:v h264 -hls_flags delete_segments \
  -hls_key_info_file file.keyinfo out.m3u8
@end example

@item -hls_enc @var{enc}
Enable (1) or disable (0) the AES128 encryption.
When enabled every segment generated is encrypted and the encryption key
is saved as @var{playlist name}.key.

@item -hls_enc_key @var{key}
Hex-coded 16byte key to encrypt the segments, by default it
is randomly generated.

@item -hls_enc_key_url @var{keyurl}
If set, @var{keyurl} is prepended instead of @var{baseurl} to the key filename
in the playlist.

@item -hls_enc_iv @var{iv}
Hex-coded 16byte initialization vector for every segment instead
of the autogenerated ones.

@item hls_segment_type @var{flags}
Possible values:

@table @samp
@item mpegts
Output segment files in MPEG-2 Transport Stream format. This is
compatible with all HLS versions.

@item fmp4
Output segment files in fragmented MP4 format, similar to MPEG-DASH.
fmp4 files may be used in HLS version 7 and above.

@end table

@item hls_fmp4_init_filename @var{filename}
Set filename to the fragment files header file, default filename is @file{init.mp4}.

@item hls_fmp4_init_resend @var{filename}
Resend init file after m3u8 file refresh every time, default is @var{0}.

When @code{var_stream_map} is set with two or more variant streams, the
@var{filename} pattern must contain the string "%v", this string specifies
the position of variant stream index in the generated init file names.
The string "%v" may be present in the filename or in the last directory name
containing the file. If the string is present in the directory name, then
sub-directories are created after expanding the directory name pattern. This
enables creation of init files corresponding to different variant streams in
subdirectories.

@item hls_flags @var{flags}
Possible values:

@table @samp
@item single_file
If this flag is set, the muxer will store all segments in a single MPEG-TS
file, and will use byte ranges in the playlist. HLS playlists generated with
this way will have the version number 4.
For example:
@example
ffmpeg -i in.nut -hls_flags single_file out.m3u8
@end example
Will produce the playlist, @file{out.m3u8}, and a single segment file,
@file{out.ts}.

@item delete_segments
Segment files removed from the playlist are deleted after a period of time
equal to the duration of the segment plus the duration of the playlist.

@item append_list
Append new segments into the end of old segment list,
and remove the @code{#EXT-X-ENDLIST} from the old segment list.

@item round_durations
Round the duration info in the playlist file segment info to integer
values, instead of using floating point.

@item discont_start
Add the @code{#EXT-X-DISCONTINUITY} tag to the playlist, before the
first segment's information.

@item omit_endlist
Do not append the @code{EXT-X-ENDLIST} tag at the end of the playlist.

@item periodic_rekey
The file specified by @code{hls_key_info_file} will be checked periodically and
detect updates to the encryption info. Be sure to replace this file atomically,
including the file containing the AES encryption key.

@item independent_segments
Add the @code{#EXT-X-INDEPENDENT-SEGMENTS} to playlists that has video segments
and when all the segments of that playlist are guaranteed to start with a Key frame.

@item iframes_only
Add the @code{#EXT-X-I-FRAMES-ONLY} to playlists that has video segments
and can play only I-frames in the @code{#EXT-X-BYTERANGE} mode.

@item split_by_time
Allow segments to start on frames other than keyframes. This improves
behavior on some players when the time between keyframes is inconsistent,
but may make things worse on others, and can cause some oddities during
seeking. This flag should be used with the @code{hls_time} option.

@item program_date_time
Generate @code{EXT-X-PROGRAM-DATE-TIME} tags.

@item second_level_segment_index
Makes it possible to use segment indexes as %%d in hls_segment_filename expression
besides date/time values when strftime is on.
To get fixed width numbers with trailing zeroes, %%0xd format is available where x is the required width.

@item second_level_segment_size
Makes it possible to use segment sizes (counted in bytes) as %%s in hls_segment_filename
expression besides date/time values when strftime is on.
To get fixed width numbers with trailing zeroes, %%0xs format is available where x is the required width.

@item second_level_segment_duration
Makes it possible to use segment duration (calculated  in microseconds) as %%t in hls_segment_filename
expression besides date/time values when strftime is on.
To get fixed width numbers with trailing zeroes, %%0xt format is available where x is the required width.

@example
ffmpeg -i sample.mpeg \
   -f hls -hls_time 3 -hls_list_size 5 \
   -hls_flags second_level_segment_index+second_level_segment_size+second_level_segment_duration \
   -strftime 1 -strftime_mkdir 1 -hls_segment_filename "segment_%Y%m%d%H%M%S_%%04d_%%08s_%%013t.ts" stream.m3u8
@end example
This will produce segments like this:
@file{segment_20170102194334_0003_00122200_0000003000000.ts}, @file{segment_20170102194334_0004_00120072_0000003000000.ts} etc.

@item temp_file
Write segment data to filename.tmp and rename to filename only once the segment is complete. A webserver
serving up segments can be configured to reject requests to *.tmp to prevent access to in-progress segments
before they have been added to the m3u8 playlist. This flag also affects how m3u8 playlist files are created.
If this flag is set, all playlist files will written into temporary file and renamed after they are complete, similarly as segments are handled.
But playlists with @code{file} protocol and with type (@code{hls_playlist_type}) other than @code{vod}
are always written into temporary file regardless of this flag. Master playlist files (@code{master_pl_name}), if any, with @code{file} protocol,
are always written into temporary file regardless of this flag if @code{master_pl_publish_rate} value is other than zero.

@end table

@item hls_playlist_type event
Emit @code{#EXT-X-PLAYLIST-TYPE:EVENT} in the m3u8 header. Forces
@option{hls_list_size} to 0; the playlist can only be appended to.

@item hls_playlist_type vod
Emit @code{#EXT-X-PLAYLIST-TYPE:VOD} in the m3u8 header. Forces
@option{hls_list_size} to 0; the playlist must not change.

@item method
Use the given HTTP method to create the hls files.
@example
ffmpeg -re -i in.ts -f hls -method PUT http://example.com/live/out.m3u8
@end example
This example will upload all the mpegts segment files to the HTTP
server using the HTTP PUT method, and update the m3u8 files every
@code{refresh} times using the same method.
Note that the HTTP server must support the given method for uploading
files.

@item http_user_agent
Override User-Agent field in HTTP header. Applicable only for HTTP output.

@item var_stream_map
Map string which specifies how to group the audio, video and subtitle streams
into different variant streams. The variant stream groups are separated
by space.
Expected string format is like this "a:0,v:0 a:1,v:1 ....". Here a:, v:, s: are
the keys to specify audio, video and subtitle streams respectively.
Allowed values are 0 to 9 (limited just based on practical usage).

When there are two or more variant streams, the output filename pattern must
contain the string "%v", this string specifies the position of variant stream
index in the output media playlist filenames. The string "%v" may be present in
the filename or in the last directory name containing the file. If the string is
present in the directory name, then sub-directories are created after expanding
the directory name pattern. This enables creation of variant streams in
subdirectories.

@example
ffmpeg -re -i in.ts -b:v:0 1000k -b:v:1 256k -b:a:0 64k -b:a:1 32k \
  -map 0:v -map 0:a -map 0:v -map 0:a -f hls -var_stream_map "v:0,a:0 v:1,a:1" \
  http://example.com/live/out_%v.m3u8
@end example
This example creates two hls variant streams. The first variant stream will
contain video stream of bitrate 1000k and audio stream of bitrate 64k and the
second variant stream will contain video stream of bitrate 256k and audio
stream of bitrate 32k. Here, two media playlist with file names out_0.m3u8 and
out_1.m3u8 will be created. If you want something meaningful text instead of indexes
in result names, you may specify names for each or some of the variants
as in the following example.


@example
ffmpeg -re -i in.ts -b:v:0 1000k -b:v:1 256k -b:a:0 64k -b:a:1 32k \
  -map 0:v -map 0:a -map 0:v -map 0:a -f hls -var_stream_map "v:0,a:0,name:my_hd v:1,a:1,name:my_sd" \
  http://example.com/live/out_%v.m3u8
@end example

This example creates two hls variant streams as in the previous one.
But here, the two media playlist with file names out_my_hd.m3u8 and
out_my_sd.m3u8 will be created.

@example
ffmpeg -re -i in.ts -b:v:0 1000k -b:v:1 256k -b:a:0 64k \
  -map 0:v -map 0:a -map 0:v -f hls -var_stream_map "v:0 a:0 v:1" \
  http://example.com/live/out_%v.m3u8
@end example
This example creates three hls variant streams. The first variant stream will
be a video only stream with video bitrate 1000k, the second variant stream will
be an audio only stream with bitrate 64k and the third variant stream will be a
video only stream with bitrate 256k. Here, three media playlist with file names
out_0.m3u8, out_1.m3u8 and out_2.m3u8 will be created.
@example
ffmpeg -re -i in.ts -b:v:0 1000k -b:v:1 256k -b:a:0 64k -b:a:1 32k \
  -map 0:v -map 0:a -map 0:v -map 0:a -f hls -var_stream_map "v:0,a:0 v:1,a:1" \
  http://example.com/live/vs_%v/out.m3u8
@end example
This example creates the variant streams in subdirectories. Here, the first
media playlist is created at @file{http://example.com/live/vs_0/out.m3u8} and
the second one at @file{http://example.com/live/vs_1/out.m3u8}.
@example
ffmpeg -re -i in.ts -b:a:0 32k -b:a:1 64k -b:v:0 1000k -b:v:1 3000k  \
  -map 0:a -map 0:a -map 0:v -map 0:v -f hls \
  -var_stream_map "a:0,agroup:aud_low a:1,agroup:aud_high v:0,agroup:aud_low v:1,agroup:aud_high" \
  -master_pl_name master.m3u8 \
  http://example.com/live/out_%v.m3u8
@end example
This example creates two audio only and two video only variant streams. In
addition to the #EXT-X-STREAM-INF tag for each variant stream in the master
playlist, #EXT-X-MEDIA tag is also added for the two audio only variant streams
and they are mapped to the two video only variant streams with audio group names
'aud_low' and 'aud_high'.

By default, a single hls variant containing all the encoded streams is created.

@example
ffmpeg -re -i in.ts -b:a:0 32k -b:a:1 64k -b:v:0 1000k \
  -map 0:a -map 0:a -map 0:v -f hls \
  -var_stream_map "a:0,agroup:aud_low,default:yes a:1,agroup:aud_low v:0,agroup:aud_low" \
  -master_pl_name master.m3u8 \
  http://example.com/live/out_%v.m3u8
@end example
This example creates two audio only and one video only variant streams. In
addition to the #EXT-X-STREAM-INF tag for each variant stream in the master
playlist, #EXT-X-MEDIA tag is also added for the two audio only variant streams
and they are mapped to the one video only variant streams with audio group name
'aud_low', and the audio group have default stat is NO or YES.

By default, a single hls variant containing all the encoded streams is created.

@example
ffmpeg -re -i in.ts -b:a:0 32k -b:a:1 64k -b:v:0 1000k \
  -map 0:a -map 0:a -map 0:v -f hls \
  -var_stream_map "a:0,agroup:aud_low,default:yes,language:ENG a:1,agroup:aud_low,language:CHN v:0,agroup:aud_low" \
  -master_pl_name master.m3u8 \
  http://example.com/live/out_%v.m3u8
@end example
This example creates two audio only and one video only variant streams. In
addition to the #EXT-X-STREAM-INF tag for each variant stream in the master
playlist, #EXT-X-MEDIA tag is also added for the two audio only variant streams
and they are mapped to the one video only variant streams with audio group name
'aud_low', and the audio group have default stat is NO or YES, and one audio
have and language is named ENG, the other audio language is named CHN.

By default, a single hls variant containing all the encoded streams is created.

@example
ffmpeg -y -i input_with_subtitle.mkv \
 -b:v:0 5250k -c:v h264 -pix_fmt yuv420p -profile:v main -level 4.1 \
 -b:a:0 256k \
 -c:s webvtt -c:a mp2 -ar 48000 -ac 2 -map 0:v -map 0:a:0 -map 0:s:0 \
 -f hls -var_stream_map "v:0,a:0,s:0,sgroup:subtitle" \
 -master_pl_name master.m3u8 -t 300 -hls_time 10 -hls_init_time 4 -hls_list_size \
 10 -master_pl_publish_rate 10  -hls_flags \
 delete_segments+discont_start+split_by_time ./tmp/video.m3u8
@end example

This example adds @code{#EXT-X-MEDIA} tag with @code{TYPE=SUBTITLES} in
the master playlist with webvtt subtitle group name 'subtitle'. Please make sure
the input file has one text subtitle stream at least.

@item cc_stream_map
Map string which specifies different closed captions groups and their
attributes. The closed captions stream groups are separated by space.
Expected string format is like this
"ccgroup:<group name>,instreamid:<INSTREAM-ID>,language:<language code> ....".
'ccgroup' and 'instreamid' are mandatory attributes. 'language' is an optional
attribute.
The closed captions groups configured using this option are mapped to different
variant streams by providing the same 'ccgroup' name in the
@code{var_stream_map} string. If @code{var_stream_map} is not set, then the
first available ccgroup in @code{cc_stream_map} is mapped to the output variant
stream. The examples for these two use cases are given below.

@example
ffmpeg -re -i in.ts -b:v 1000k -b:a 64k -a53cc 1 -f hls \
  -cc_stream_map "ccgroup:cc,instreamid:CC1,language:en" \
  -master_pl_name master.m3u8 \
  http://example.com/live/out.m3u8
@end example
This example adds @code{#EXT-X-MEDIA} tag with @code{TYPE=CLOSED-CAPTIONS} in
the master playlist with group name 'cc', language 'en' (english) and
INSTREAM-ID 'CC1'. Also, it adds @code{CLOSED-CAPTIONS} attribute with group
name 'cc' for the output variant stream.
@example
ffmpeg -re -i in.ts -b:v:0 1000k -b:v:1 256k -b:a:0 64k -b:a:1 32k \
  -a53cc:0 1 -a53cc:1 1\
  -map 0:v -map 0:a -map 0:v -map 0:a -f hls \
  -cc_stream_map "ccgroup:cc,instreamid:CC1,language:en ccgroup:cc,instreamid:CC2,language:sp" \
  -var_stream_map "v:0,a:0,ccgroup:cc v:1,a:1,ccgroup:cc" \
  -master_pl_name master.m3u8 \
  http://example.com/live/out_%v.m3u8
@end example
This example adds two @code{#EXT-X-MEDIA} tags with @code{TYPE=CLOSED-CAPTIONS} in
the master playlist for the INSTREAM-IDs 'CC1' and 'CC2'. Also, it adds
@code{CLOSED-CAPTIONS} attribute with group name 'cc' for the two output variant
streams.

@item master_pl_name
Create HLS master playlist with the given name.

@example
ffmpeg -re -i in.ts -f hls -master_pl_name master.m3u8 http://example.com/live/out.m3u8
@end example
This example creates HLS master playlist with name master.m3u8 and it is
published at http://example.com/live/

@item master_pl_publish_rate
Publish master play list repeatedly every after specified number of segment intervals.

@example
ffmpeg -re -i in.ts -f hls -master_pl_name master.m3u8 \
-hls_time 2 -master_pl_publish_rate 30 http://example.com/live/out.m3u8
@end example

This example creates HLS master playlist with name master.m3u8 and keep
publishing it repeatedly every after 30 segments i.e. every after 60s.

@item http_persistent
Use persistent HTTP connections. Applicable only for HTTP output.

@item timeout
Set timeout for socket I/O operations. Applicable only for HTTP output.

@item -ignore_io_errors
Ignore IO errors during open, write and delete. Useful for long-duration runs with network output.

@item headers
Set custom HTTP headers, can override built in default headers. Applicable only for HTTP output.

@end table

@anchor{ico}
@section ico

ICO file muxer.

Microsoft's icon file format (ICO) has some strict limitations that should be noted:

@itemize
@item
Size cannot exceed 256 pixels in any dimension

@item
Only BMP and PNG images can be stored

@item
If a BMP image is used, it must be one of the following pixel formats:
@example
BMP Bit Depth      FFmpeg Pixel Format
1bit               pal8
4bit               pal8
8bit               pal8
16bit              rgb555le
24bit              bgr24
32bit              bgra
@end example

@item
If a BMP image is used, it must use the BITMAPINFOHEADER DIB header

@item
If a PNG image is used, it must use the rgba pixel format
@end itemize

@anchor{image2}
@section image2

Image file muxer.

The image file muxer writes video frames to image files.

The output filenames are specified by a pattern, which can be used to
produce sequentially numbered series of files.
The pattern may contain the string "%d" or "%0@var{N}d", this string
specifies the position of the characters representing a numbering in
the filenames. If the form "%0@var{N}d" is used, the string
representing the number in each filename is 0-padded to @var{N}
digits. The literal character '%' can be specified in the pattern with
the string "%%".

If the pattern contains "%d" or "%0@var{N}d", the first filename of
the file list specified will contain the number 1, all the following
numbers will be sequential.

The pattern may contain a suffix which is used to automatically
determine the format of the image files to write.

For example the pattern "img-%03d.bmp" will specify a sequence of
filenames of the form @file{img-001.bmp}, @file{img-002.bmp}, ...,
@file{img-010.bmp}, etc.
The pattern "img%%-%d.jpg" will specify a sequence of filenames of the
form @file{img%-1.jpg}, @file{img%-2.jpg}, ..., @file{img%-10.jpg},
etc.

The image muxer supports the .Y.U.V image file format. This format is
special in that that each image frame consists of three files, for
each of the YUV420P components. To read or write this image file format,
specify the name of the '.Y' file. The muxer will automatically open the
'.U' and '.V' files as required.

@subsection Options

@table @option
@item frame_pts
If set to 1, expand the filename with pts from pkt->pts.
Default value is 0.

@item start_number
Start the sequence from the specified number. Default value is 1.

@item update
If set to 1, the filename will always be interpreted as just a
filename, not a pattern, and the corresponding file will be continuously
overwritten with new images. Default value is 0.

@item strftime
If set to 1, expand the filename with date and time information from
@code{strftime()}. Default value is 0.

@item protocol_opts @var{options_list}
Set protocol options as a :-separated list of key=value parameters. Values
containing the @code{:} special character must be escaped.

@end table

@subsection Examples

The following example shows how to use @command{ffmpeg} for creating a
sequence of files @file{img-001.jpeg}, @file{img-002.jpeg}, ...,
taking one image every second from the input video:
@example
ffmpeg -i in.avi -vsync cfr -r 1 -f image2 'img-%03d.jpeg'
@end example

Note that with @command{ffmpeg}, if the format is not specified with the
@code{-f} option and the output filename specifies an image file
format, the image2 muxer is automatically selected, so the previous
command can be written as:
@example
ffmpeg -i in.avi -vsync cfr -r 1 'img-%03d.jpeg'
@end example

Note also that the pattern must not necessarily contain "%d" or
"%0@var{N}d", for example to create a single image file
@file{img.jpeg} from the start of the input video you can employ the command:
@example
ffmpeg -i in.avi -f image2 -frames:v 1 img.jpeg
@end example

The @option{strftime} option allows you to expand the filename with
date and time information. Check the documentation of
the @code{strftime()} function for the syntax.

For example to generate image files from the @code{strftime()}
"%Y-%m-%d_%H-%M-%S" pattern, the following @command{ffmpeg} command
can be used:
@example
ffmpeg -f v4l2 -r 1 -i /dev/video0 -f image2 -strftime 1 "%Y-%m-%d_%H-%M-%S.jpg"
@end example

You can set the file name with current frame's PTS:
@example
ffmpeg -f v4l2 -r 1 -i /dev/video0 -copyts -f image2 -frame_pts true %d.jpg"
@end example

A more complex example is to publish contents of your desktop directly to a
WebDAV server every second:
@example
ffmpeg -f x11grab -framerate 1 -i :0.0 -q:v 6 -update 1 -protocol_opts method=PUT http://example.com/desktop.jpg
@end example

@section matroska

Matroska container muxer.

This muxer implements the matroska and webm container specs.

@subsection Metadata

The recognized metadata settings in this muxer are:

@table @option
@item title
Set title name provided to a single track.

@item language
Specify the language of the track in the Matroska languages form.

The language can be either the 3 letters bibliographic ISO-639-2 (ISO
639-2/B) form (like "fre" for French), or a language code mixed with a
country code for specialities in languages (like "fre-ca" for Canadian
French).

@item stereo_mode
Set stereo 3D video layout of two views in a single video track.

The following values are recognized:
@table @samp
@item mono
video is not stereo
@item left_right
Both views are arranged side by side, Left-eye view is on the left
@item bottom_top
Both views are arranged in top-bottom orientation, Left-eye view is at bottom
@item top_bottom
Both views are arranged in top-bottom orientation, Left-eye view is on top
@item checkerboard_rl
Each view is arranged in a checkerboard interleaved pattern, Left-eye view being first
@item checkerboard_lr
Each view is arranged in a checkerboard interleaved pattern, Right-eye view being first
@item row_interleaved_rl
Each view is constituted by a row based interleaving, Right-eye view is first row
@item row_interleaved_lr
Each view is constituted by a row based interleaving, Left-eye view is first row
@item col_interleaved_rl
Both views are arranged in a column based interleaving manner, Right-eye view is first column
@item col_interleaved_lr
Both views are arranged in a column based interleaving manner, Left-eye view is first column
@item anaglyph_cyan_red
All frames are in anaglyph format viewable through red-cyan filters
@item right_left
Both views are arranged side by side, Right-eye view is on the left
@item anaglyph_green_magenta
All frames are in anaglyph format viewable through green-magenta filters
@item block_lr
Both eyes laced in one Block, Left-eye view is first
@item block_rl
Both eyes laced in one Block, Right-eye view is first
@end table
@end table

For example a 3D WebM clip can be created using the following command line:
@example
ffmpeg -i sample_left_right_clip.mpg -an -c:v libvpx -metadata stereo_mode=left_right -y stereo_clip.webm
@end example

@subsection Options

This muxer supports the following options:

@table @option
@item reserve_index_space
By default, this muxer writes the index for seeking (called cues in Matroska
terms) at the end of the file, because it cannot know in advance how much space
to leave for the index at the beginning of the file. However for some use cases
-- e.g.  streaming where seeking is possible but slow -- it is useful to put the
index at the beginning of the file.

If this option is set to a non-zero value, the muxer will reserve a given amount
of space in the file header and then try to write the cues there when the muxing
finishes. If the reserved space does not suffice, no Cues will be written, the
file will be finalized and writing the trailer will return an error.
A safe size for most use cases should be about 50kB per hour of video.

Note that cues are only written if the output is seekable and this option will
have no effect if it is not.
@end table

@anchor{md5}
@section md5

MD5 testing format.

This is a variant of the @ref{hash} muxer. Unlike that muxer, it
defaults to using the MD5 hash function.

@subsection Examples

To compute the MD5 hash of the input converted to raw
audio and video, and store it in the file @file{out.md5}:
@example
ffmpeg -i INPUT -f md5 out.md5
@end example

You can print the MD5 to stdout with the command:
@example
ffmpeg -i INPUT -f md5 -
@end example

See also the @ref{hash} and @ref{framemd5} muxers.

@section mov, mp4, ismv

MOV/MP4/ISMV (Smooth Streaming) muxer.

The mov/mp4/ismv muxer supports fragmentation. Normally, a MOV/MP4
file has all the metadata about all packets stored in one location
(written at the end of the file, it can be moved to the start for
better playback by adding @var{faststart} to the @var{movflags}, or
using the @command{qt-faststart} tool). A fragmented
file consists of a number of fragments, where packets and metadata
about these packets are stored together. Writing a fragmented
file has the advantage that the file is decodable even if the
writing is interrupted (while a normal MOV/MP4 is undecodable if
it is not properly finished), and it requires less memory when writing
very long files (since writing normal MOV/MP4 files stores info about
every single packet in memory until the file is closed). The downside
is that it is less compatible with other applications.

@subsection Options

Fragmentation is enabled by setting one of the AVOptions that define
how to cut the file into fragments:

@table @option
@item -moov_size @var{bytes}
Reserves space for the moov atom at the beginning of the file instead of placing the
moov atom at the end. If the space reserved is insufficient, muxing will fail.
@item -movflags frag_keyframe
Start a new fragment at each video keyframe.
@item -frag_duration @var{duration}
Create fragments that are @var{duration} microseconds long.
@item -frag_size @var{size}
Create fragments that contain up to @var{size} bytes of payload data.
@item -movflags frag_custom
Allow the caller to manually choose when to cut fragments, by
calling @code{av_write_frame(ctx, NULL)} to write a fragment with
the packets written so far. (This is only useful with other
applications integrating libavformat, not from @command{ffmpeg}.)
@item -min_frag_duration @var{duration}
Don't create fragments that are shorter than @var{duration} microseconds long.
@end table

If more than one condition is specified, fragments are cut when
one of the specified conditions is fulfilled. The exception to this is
@code{-min_frag_duration}, which has to be fulfilled for any of the other
conditions to apply.

Additionally, the way the output file is written can be adjusted
through a few other options:

@table @option
@item -movflags empty_moov
Write an initial moov atom directly at the start of the file, without
describing any samples in it. Generally, an mdat/moov pair is written
at the start of the file, as a normal MOV/MP4 file, containing only
a short portion of the file. With this option set, there is no initial
mdat atom, and the moov atom only describes the tracks but has
a zero duration.

This option is implicitly set when writing ismv (Smooth Streaming) files.
@item -movflags separate_moof
Write a separate moof (movie fragment) atom for each track. Normally,
packets for all tracks are written in a moof atom (which is slightly
more efficient), but with this option set, the muxer writes one moof/mdat
pair for each track, making it easier to separate tracks.

This option is implicitly set when writing ismv (Smooth Streaming) files.
@item -movflags skip_sidx
Skip writing of sidx atom. When bitrate overhead due to sidx atom is high,
this option could be used for cases where sidx atom is not mandatory.
When global_sidx flag is enabled, this option will be ignored.
@item -movflags faststart
Run a second pass moving the index (moov atom) to the beginning of the file.
This operation can take a while, and will not work in various situations such
as fragmented output, thus it is not enabled by default.
@item -movflags rtphint
Add RTP hinting tracks to the output file.
@item -movflags disable_chpl
Disable Nero chapter markers (chpl atom).  Normally, both Nero chapters
and a QuickTime chapter track are written to the file. With this option
set, only the QuickTime chapter track will be written. Nero chapters can
cause failures when the file is reprocessed with certain tagging programs, like
mp3Tag 2.61a and iTunes 11.3, most likely other versions are affected as well.
@item -movflags omit_tfhd_offset
Do not write any absolute base_data_offset in tfhd atoms. This avoids
tying fragments to absolute byte positions in the file/streams.
@item -movflags default_base_moof
Similarly to the omit_tfhd_offset, this flag avoids writing the
absolute base_data_offset field in tfhd atoms, but does so by using
the new default-base-is-moof flag instead. This flag is new from
14496-12:2012. This may make the fragments easier to parse in certain
circumstances (avoiding basing track fragment location calculations
on the implicit end of the previous track fragment).
@item -write_tmcd
Specify @code{on} to force writing a timecode track, @code{off} to disable it
and @code{auto} to write a timecode track only for mov and mp4 output (default).
@item -movflags negative_cts_offsets
Enables utilization of version 1 of the CTTS box, in which the CTS offsets can
be negative. This enables the initial sample to have DTS/CTS of zero, and
reduces the need for edit lists for some cases such as video tracks with
B-frames. Additionally, eases conformance with the DASH-IF interoperability
guidelines.

This option is implicitly set when writing ismv (Smooth Streaming) files.
@item -write_prft
Write producer time reference box (PRFT) with a specified time source for the
NTP field in the PRFT box. Set value as @samp{wallclock} to specify timesource
as wallclock time and @samp{pts} to specify timesource as input packets' PTS
values.

Setting value to @samp{pts} is applicable only for a live encoding use case,
where PTS values are set as as wallclock time at the source. For example, an
encoding use case with decklink capture source where @option{video_pts} and
@option{audio_pts} are set to @samp{abs_wallclock}.
@end table

@subsection Example

Smooth Streaming content can be pushed in real time to a publishing
point on IIS with this muxer. Example:
@example
ffmpeg -re @var{<normal input/transcoding options>} -movflags isml+frag_keyframe -f ismv http://server/publishingpoint.isml/Streams(Encoder1)
@end example

@section mp3

The MP3 muxer writes a raw MP3 stream with the following optional features:
@itemize @bullet
@item
An ID3v2 metadata header at the beginning (enabled by default). Versions 2.3 and
2.4 are supported, the @code{id3v2_version} private option controls which one is
used (3 or 4). Setting @code{id3v2_version} to 0 disables the ID3v2 header
completely.

The muxer supports writing attached pictures (APIC frames) to the ID3v2 header.
The pictures are supplied to the muxer in form of a video stream with a single
packet. There can be any number of those streams, each will correspond to a
single APIC frame.  The stream metadata tags @var{title} and @var{comment} map
to APIC @var{description} and @var{picture type} respectively. See
@url{http://id3.org/id3v2.4.0-frames} for allowed picture types.

Note that the APIC frames must be written at the beginning, so the muxer will
buffer the audio frames until it gets all the pictures. It is therefore advised
to provide the pictures as soon as possible to avoid excessive buffering.

@item
A Xing/LAME frame right after the ID3v2 header (if present). It is enabled by
default, but will be written only if the output is seekable. The
@code{write_xing} private option can be used to disable it.  The frame contains
various information that may be useful to the decoder, like the audio duration
or encoder delay.

@item
A legacy ID3v1 tag at the end of the file (disabled by default). It may be
enabled with the @code{write_id3v1} private option, but as its capabilities are
very limited, its usage is not recommended.
@end itemize

Examples:

Write an mp3 with an ID3v2.3 header and an ID3v1 footer:
@example
ffmpeg -i INPUT -id3v2_version 3 -write_id3v1 1 out.mp3
@end example

To attach a picture to an mp3 file select both the audio and the picture stream
with @code{map}:
@example
ffmpeg -i input.mp3 -i cover.png -c copy -map 0 -map 1
-metadata:s:v title="Album cover" -metadata:s:v comment="Cover (Front)" out.mp3
@end example

Write a "clean" MP3 without any extra features:
@example
ffmpeg -i input.wav -write_xing 0 -id3v2_version 0 out.mp3
@end example

@section mpegts

MPEG transport stream muxer.

This muxer implements ISO 13818-1 and part of ETSI EN 300 468.

The recognized metadata settings in mpegts muxer are @code{service_provider}
and @code{service_name}. If they are not set the default for
@code{service_provider} is @samp{FFmpeg} and the default for
@code{service_name} is @samp{Service01}.

@subsection Options

The muxer options are:

@table @option
@item mpegts_transport_stream_id @var{integer}
Set the @samp{transport_stream_id}. This identifies a transponder in DVB.
Default is @code{0x0001}.

@item mpegts_original_network_id @var{integer}
Set the @samp{original_network_id}. This is unique identifier of a
network in DVB. Its main use is in the unique identification of a service
through the path @samp{Original_Network_ID, Transport_Stream_ID}. Default
is @code{0x0001}.

@item mpegts_service_id @var{integer}
Set the @samp{service_id}, also known as program in DVB. Default is
@code{0x0001}.

@item mpegts_service_type @var{integer}
Set the program @samp{service_type}. Default is @code{digital_tv}.
Accepts the following options:
@table @samp
@item hex_value
Any hexadecimal value between @code{0x01} and @code{0xff} as defined in
ETSI 300 468.
@item digital_tv
Digital TV service.
@item digital_radio
Digital Radio service.
@item teletext
Teletext service.
@item advanced_codec_digital_radio
Advanced Codec Digital Radio service.
@item mpeg2_digital_hdtv
MPEG2 Digital HDTV service.
@item advanced_codec_digital_sdtv
Advanced Codec Digital SDTV service.
@item advanced_codec_digital_hdtv
Advanced Codec Digital HDTV service.
@end table

@item mpegts_pmt_start_pid @var{integer}
Set the first PID for PMTs. Default is @code{0x1000}, minimum is @code{0x0020},
maximum is @code{0x1ffa}.

@item mpegts_start_pid @var{integer}
Set the first PID for elementary streams. Default is @code{0x0100}, minimum is
@code{0x0020}, maximum is @code{0x1ffa}.

@item mpegts_m2ts_mode @var{boolean}
Enable m2ts mode if set to @code{1}. Default value is @code{-1} which
disables m2ts mode.

@item muxrate @var{integer}
Set a constant muxrate. Default is VBR.

@item pes_payload_size @var{integer}
Set minimum PES packet payload in bytes. Default is @code{2930}.

@item mpegts_flags @var{flags}
Set mpegts flags. Accepts the following options:
@table @samp
@item resend_headers
Reemit PAT/PMT before writing the next packet.
@item latm
Use LATM packetization for AAC.
@item pat_pmt_at_frames
Reemit PAT and PMT at each video frame.
@item system_b
Conform to System B (DVB) instead of System A (ATSC).
@item initial_discontinuity
Mark the initial packet of each stream as discontinuity.
@end table

@item mpegts_copyts @var{boolean}
Preserve original timestamps, if value is set to @code{1}. Default value
is @code{-1}, which results in shifting timestamps so that they start from 0.

@item omit_video_pes_length @var{boolean}
Omit the PES packet length for video packets. Default is @code{1} (true).

@item pcr_period @var{integer}
Override the default PCR retransmission time in milliseconds. Default is
@code{-1} which means that the PCR interval will be determined automatically:
20 ms is used for CBR streams, the highest multiple of the frame duration which
is less than 100 ms is used for VBR streams.

@item pat_period @var{duration}
Maximum time in seconds between PAT/PMT tables. Default is @code{0.1}.

@item sdt_period @var{duration}
Maximum time in seconds between SDT tables. Default is @code{0.5}.

@item tables_version @var{integer}
Set PAT, PMT and SDT version (default @code{0}, valid values are from 0 to 31, inclusively).
This option allows updating stream structure so that standard consumer may
detect the change. To do so, reopen output @code{AVFormatContext} (in case of API
usage) or restart @command{ffmpeg} instance, cyclically changing
@option{tables_version} value:

@example
ffmpeg -i source1.ts -codec copy -f mpegts -tables_version 0 udp://1.1.1.1:1111
ffmpeg -i source2.ts -codec copy -f mpegts -tables_version 1 udp://1.1.1.1:1111
...
ffmpeg -i source3.ts -codec copy -f mpegts -tables_version 31 udp://1.1.1.1:1111
ffmpeg -i source1.ts -codec copy -f mpegts -tables_version 0 udp://1.1.1.1:1111
ffmpeg -i source2.ts -codec copy -f mpegts -tables_version 1 udp://1.1.1.1:1111
...
@end example
@end table

@subsection Example

@example
ffmpeg -i file.mpg -c copy \
     -mpegts_original_network_id 0x1122 \
     -mpegts_transport_stream_id 0x3344 \
     -mpegts_service_id 0x5566 \
     -mpegts_pmt_start_pid 0x1500 \
     -mpegts_start_pid 0x150 \
     -metadata service_provider="Some provider" \
     -metadata service_name="Some Channel" \
     out.ts
@end example

@section mxf, mxf_d10, mxf_opatom

MXF muxer.

@subsection Options

The muxer options are:

@table @option
@item store_user_comments @var{bool}
Set if user comments should be stored if available or never.
IRT D-10 does not allow user comments. The default is thus to write them for
mxf and mxf_opatom but not for mxf_d10
@end table

@section null

Null muxer.

This muxer does not generate any output file, it is mainly useful for
testing or benchmarking purposes.

For example to benchmark decoding with @command{ffmpeg} you can use the
command:
@example
ffmpeg -benchmark -i INPUT -f null out.null
@end example

Note that the above command does not read or write the @file{out.null}
file, but specifying the output file is required by the @command{ffmpeg}
syntax.

Alternatively you can write the command as:
@example
ffmpeg -benchmark -i INPUT -f null -
@end example

@section nut

@table @option
@item -syncpoints @var{flags}
Change the syncpoint usage in nut:
@table @option
@item @var{default} use the normal low-overhead seeking aids.
@item @var{none} do not use the syncpoints at all, reducing the overhead but making the stream non-seekable;
    Use of this option is not recommended, as the resulting files are very damage
    sensitive and seeking is not possible. Also in general the overhead from
    syncpoints is negligible. Note, -@code{write_index} 0 can be used to disable
    all growing data tables, allowing to mux endless streams with limited memory
    and without these disadvantages.
@item @var{timestamped} extend the syncpoint with a wallclock field.
@end table
The @var{none} and @var{timestamped} flags are experimental.
@item -write_index @var{bool}
Write index at the end, the default is to write an index.
@end table

@example
ffmpeg -i INPUT -f_strict experimental -syncpoints none - | processor
@end example

@section ogg

Ogg container muxer.

@table @option
@item -page_duration @var{duration}
Preferred page duration, in microseconds. The muxer will attempt to create
pages that are approximately @var{duration} microseconds long. This allows the
user to compromise between seek granularity and container overhead. The default
is 1 second. A value of 0 will fill all segments, making pages as large as
possible. A value of 1 will effectively use 1 packet-per-page in most
situations, giving a small seek granularity at the cost of additional container
overhead.
@item -serial_offset @var{value}
Serial value from which to set the streams serial number.
Setting it to different and sufficiently large values ensures that the produced
ogg files can be safely chained.

@end table

@anchor{segment}
@section segment, stream_segment, ssegment

Basic stream segmenter.

This muxer outputs streams to a number of separate files of nearly
fixed duration. Output filename pattern can be set in a fashion
similar to @ref{image2}, or by using a @code{strftime} template if
the @option{strftime} option is enabled.

@code{stream_segment} is a variant of the muxer used to write to
streaming output formats, i.e. which do not require global headers,
and is recommended for outputting e.g. to MPEG transport stream segments.
@code{ssegment} is a shorter alias for @code{stream_segment}.

Every segment starts with a keyframe of the selected reference stream,
which is set through the @option{reference_stream} option.

Note that if you want accurate splitting for a video file, you need to
make the input key frames correspond to the exact splitting times
expected by the segmenter, or the segment muxer will start the new
segment with the key frame found next after the specified start
time.

The segment muxer works best with a single constant frame rate video.

Optionally it can generate a list of the created segments, by setting
the option @var{segment_list}. The list type is specified by the
@var{segment_list_type} option. The entry filenames in the segment
list are set by default to the basename of the corresponding segment
files.

See also the @ref{hls} muxer, which provides a more specific
implementation for HLS segmentation.

@subsection Options

The segment muxer supports the following options:

@table @option
@item increment_tc @var{1|0}
if set to @code{1}, increment timecode between each segment
If this is selected, the input need to have
a timecode in the first video stream. Default value is
@code{0}.

@item reference_stream @var{specifier}
Set the reference stream, as specified by the string @var{specifier}.
If @var{specifier} is set to @code{auto}, the reference is chosen
automatically. Otherwise it must be a stream specifier (see the ``Stream
specifiers'' chapter in the ffmpeg manual) which specifies the
reference stream. The default value is @code{auto}.

@item segment_format @var{format}
Override the inner container format, by default it is guessed by the filename
extension.

@item segment_format_options @var{options_list}
Set output format options using a :-separated list of key=value
parameters. Values containing the @code{:} special character must be
escaped.

@item segment_list @var{name}
Generate also a listfile named @var{name}. If not specified no
listfile is generated.

@item segment_list_flags @var{flags}
Set flags affecting the segment list generation.

It currently supports the following flags:
@table @samp
@item cache
Allow caching (only affects M3U8 list files).

@item live
Allow live-friendly file generation.
@end table

@item segment_list_size @var{size}
Update the list file so that it contains at most @var{size}
segments. If 0 the list file will contain all the segments. Default
value is 0.

@item segment_list_entry_prefix @var{prefix}
Prepend @var{prefix} to each entry. Useful to generate absolute paths.
By default no prefix is applied.

@item segment_list_type @var{type}
Select the listing format.

The following values are recognized:
@table @samp
@item flat
Generate a flat list for the created segments, one segment per line.

@item csv, ext
Generate a list for the created segments, one segment per line,
each line matching the format (comma-separated values):
@example
@var{segment_filename},@var{segment_start_time},@var{segment_end_time}
@end example

@var{segment_filename} is the name of the output file generated by the
muxer according to the provided pattern. CSV escaping (according to
RFC4180) is applied if required.

@var{segment_start_time} and @var{segment_end_time} specify
the segment start and end time expressed in seconds.

A list file with the suffix @code{".csv"} or @code{".ext"} will
auto-select this format.

@samp{ext} is deprecated in favor or @samp{csv}.

@item ffconcat
Generate an ffconcat file for the created segments. The resulting file
can be read using the FFmpeg @ref{concat} demuxer.

A list file with the suffix @code{".ffcat"} or @code{".ffconcat"} will
auto-select this format.

@item m3u8
Generate an extended M3U8 file, version 3, compliant with
@url{http://tools.ietf.org/id/draft-pantos-http-live-streaming}.

A list file with the suffix @code{".m3u8"} will auto-select this format.
@end table

If not specified the type is guessed from the list file name suffix.

@item segment_time @var{time}
Set segment duration to @var{time}, the value must be a duration
specification. Default value is "2". See also the
@option{segment_times} option.

Note that splitting may not be accurate, unless you force the
reference stream key-frames at the given time. See the introductory
notice and the examples below.

@item segment_atclocktime @var{1|0}
If set to "1" split at regular clock time intervals starting from 00:00
o'clock. The @var{time} value specified in @option{segment_time} is
used for setting the length of the splitting interval.

For example with @option{segment_time} set to "900" this makes it possible
to create files at 12:00 o'clock, 12:15, 12:30, etc.

Default value is "0".

@item segment_clocktime_offset @var{duration}
Delay the segment splitting times with the specified duration when using
@option{segment_atclocktime}.

For example with @option{segment_time} set to "900" and
@option{segment_clocktime_offset} set to "300" this makes it possible to
create files at 12:05, 12:20, 12:35, etc.

Default value is "0".

@item segment_clocktime_wrap_duration @var{duration}
Force the segmenter to only start a new segment if a packet reaches the muxer
within the specified duration after the segmenting clock time. This way you
can make the segmenter more resilient to backward local time jumps, such as
leap seconds or transition to standard time from daylight savings time.

Default is the maximum possible duration which means starting a new segment
regardless of the elapsed time since the last clock time.

@item segment_time_delta @var{delta}
Specify the accuracy time when selecting the start time for a
segment, expressed as a duration specification. Default value is "0".

When delta is specified a key-frame will start a new segment if its
PTS satisfies the relation:
@example
PTS >= start_time - time_delta
@end example

This option is useful when splitting video content, which is always
split at GOP boundaries, in case a key frame is found just before the
specified split time.

In particular may be used in combination with the @file{ffmpeg} option
@var{force_key_frames}. The key frame times specified by
@var{force_key_frames} may not be set accurately because of rounding
issues, with the consequence that a key frame time may result set just
before the specified time. For constant frame rate videos a value of
1/(2*@var{frame_rate}) should address the worst case mismatch between
the specified time and the time set by @var{force_key_frames}.

@item segment_times @var{times}
Specify a list of split points. @var{times} contains a list of comma
separated duration specifications, in increasing order. See also
the @option{segment_time} option.

@item segment_frames @var{frames}
Specify a list of split video frame numbers. @var{frames} contains a
list of comma separated integer numbers, in increasing order.

This option specifies to start a new segment whenever a reference
stream key frame is found and the sequential number (starting from 0)
of the frame is greater or equal to the next value in the list.

@item segment_wrap @var{limit}
Wrap around segment index once it reaches @var{limit}.

@item segment_start_number @var{number}
Set the sequence number of the first segment. Defaults to @code{0}.

@item strftime @var{1|0}
Use the @code{strftime} function to define the name of the new
segments to write. If this is selected, the output segment name must
contain a @code{strftime} function template. Default value is
@code{0}.

@item break_non_keyframes @var{1|0}
If enabled, allow segments to start on frames other than keyframes. This
improves behavior on some players when the time between keyframes is
inconsistent, but may make things worse on others, and can cause some oddities
during seeking. Defaults to @code{0}.

@item reset_timestamps @var{1|0}
Reset timestamps at the beginning of each segment, so that each segment
will start with near-zero timestamps. It is meant to ease the playback
of the generated segments. May not work with some combinations of
muxers/codecs. It is set to @code{0} by default.

@item initial_offset @var{offset}
Specify timestamp offset to apply to the output packet timestamps. The
argument must be a time duration specification, and defaults to 0.

@item write_empty_segments @var{1|0}
If enabled, write an empty segment if there are no packets during the period a
segment would usually span. Otherwise, the segment will be filled with the next
packet written. Defaults to @code{0}.
@end table

Make sure to require a closed GOP when encoding and to set the GOP
size to fit your segment time constraint.

@subsection Examples

@itemize
@item
Remux the content of file @file{in.mkv} to a list of segments
@file{out-000.nut}, @file{out-001.nut}, etc., and write the list of
generated segments to @file{out.list}:
@example
ffmpeg -i in.mkv -codec hevc -flags +cgop -g 60 -map 0 -f segment -segment_list out.list out%03d.nut
@end example

@item
Segment input and set output format options for the output segments:
@example
ffmpeg -i in.mkv -f segment -segment_time 10 -segment_format_options movflags=+faststart out%03d.mp4
@end example

@item
Segment the input file according to the split points specified by the
@var{segment_times} option:
@example
ffmpeg -i in.mkv -codec copy -map 0 -f segment -segment_list out.csv -segment_times 1,2,3,5,8,13,21 out%03d.nut
@end example

@item
Use the @command{ffmpeg} @option{force_key_frames}
option to force key frames in the input at the specified location, together
with the segment option @option{segment_time_delta} to account for
possible roundings operated when setting key frame times.
@example
ffmpeg -i in.mkv -force_key_frames 1,2,3,5,8,13,21 -codec:v mpeg4 -codec:a pcm_s16le -map 0 \
-f segment -segment_list out.csv -segment_times 1,2,3,5,8,13,21 -segment_time_delta 0.05 out%03d.nut
@end example
In order to force key frames on the input file, transcoding is
required.

@item
Segment the input file by splitting the input file according to the
frame numbers sequence specified with the @option{segment_frames} option:
@example
ffmpeg -i in.mkv -codec copy -map 0 -f segment -segment_list out.csv -segment_frames 100,200,300,500,800 out%03d.nut
@end example

@item
Convert the @file{in.mkv} to TS segments using the @code{libx264}
and @code{aac} encoders:
@example
ffmpeg -i in.mkv -map 0 -codec:v libx264 -codec:a aac -f ssegment -segment_list out.list out%03d.ts
@end example

@item
Segment the input file, and create an M3U8 live playlist (can be used
as live HLS source):
@example
ffmpeg -re -i in.mkv -codec copy -map 0 -f segment -segment_list playlist.m3u8 \
-segment_list_flags +live -segment_time 10 out%03d.mkv
@end example
@end itemize

@section smoothstreaming

Smooth Streaming muxer generates a set of files (Manifest, chunks) suitable for serving with conventional web server.

@table @option
@item window_size
Specify the number of fragments kept in the manifest. Default 0 (keep all).

@item extra_window_size
Specify the number of fragments kept outside of the manifest before removing from disk. Default 5.

@item lookahead_count
Specify the number of lookahead fragments. Default 2.

@item min_frag_duration
Specify the minimum fragment duration (in microseconds). Default 5000000.

@item remove_at_exit
Specify whether to remove all fragments when finished. Default 0 (do not remove).

@end table

@anchor{streamhash}
@section streamhash

Per stream hash testing format.

This muxer computes and prints a cryptographic hash of all the input frames,
on a per-stream basis. This can be used for equality checks without having
to do a complete binary comparison.

By default audio frames are converted to signed 16-bit raw audio and
video frames to raw video before computing the hash, but the output
of explicit conversions to other codecs can also be used. Timestamps
are ignored. It uses the SHA-256 cryptographic hash function by default,
but supports several other algorithms.

The output of the muxer consists of one line per stream of the form:
@var{streamindex},@var{streamtype},@var{algo}=@var{hash}, where
@var{streamindex} is the index of the mapped stream, @var{streamtype} is a
single character indicating the type of stream, @var{algo} is a short string
representing the hash function used, and @var{hash} is a hexadecimal number
representing the computed hash.

@table @option
@item hash @var{algorithm}
Use the cryptographic hash function specified by the string @var{algorithm}.
Supported values include @code{MD5}, @code{murmur3}, @code{RIPEMD128},
@code{RIPEMD160}, @code{RIPEMD256}, @code{RIPEMD320}, @code{SHA160},
@code{SHA224}, @code{SHA256} (default), @code{SHA512/224}, @code{SHA512/256},
@code{SHA384}, @code{SHA512}, @code{CRC32} and @code{adler32}.

@end table

@subsection Examples

To compute the SHA-256 hash of the input converted to raw audio and
video, and store it in the file @file{out.sha256}:
@example
ffmpeg -i INPUT -f streamhash out.sha256
@end example

To print an MD5 hash to stdout use the command:
@example
ffmpeg -i INPUT -f streamhash -hash md5 -
@end example

See also the @ref{hash} and @ref{framehash} muxers.

@anchor{fifo}
@section fifo

The fifo pseudo-muxer allows the separation of encoding and muxing by using
first-in-first-out queue and running the actual muxer in a separate thread. This
is especially useful in combination with the @ref{tee} muxer and can be used to
send data to several destinations with different reliability/writing speed/latency.

API users should be aware that callback functions (interrupt_callback,
io_open and io_close) used within its AVFormatContext must be thread-safe.

The behavior of the fifo muxer if the queue fills up or if the output fails is
selectable,

@itemize @bullet

@item
output can be transparently restarted with configurable delay between retries
based on real time or time of the processed stream.

@item
encoding can be blocked during temporary failure, or continue transparently
dropping packets in case fifo queue fills up.

@end itemize

@table @option

@item fifo_format
Specify the format name. Useful if it cannot be guessed from the
output name suffix.

@item queue_size
Specify size of the queue (number of packets). Default value is 60.

@item format_opts
Specify format options for the underlying muxer. Muxer options can be specified
as a list of @var{key}=@var{value} pairs separated by ':'.

@item drop_pkts_on_overflow @var{bool}
If set to 1 (true), in case the fifo queue fills up, packets will be dropped
rather than blocking the encoder. This makes it possible to continue streaming without
delaying the input, at the cost of omitting part of the stream. By default
this option is set to 0 (false), so in such cases the encoder will be blocked
until the muxer processes some of the packets and none of them is lost.

@item attempt_recovery @var{bool}
If failure occurs, attempt to recover the output. This is especially useful
when used with network output, since it makes it possible to restart streaming transparently.
By default this option is set to 0 (false).

@item max_recovery_attempts
Sets maximum number of successive unsuccessful recovery attempts after which
the output fails permanently. By default this option is set to 0 (unlimited).

@item recovery_wait_time @var{duration}
Waiting time before the next recovery attempt after previous unsuccessful
recovery attempt. Default value is 5 seconds.

@item recovery_wait_streamtime @var{bool}
If set to 0 (false), the real time is used when waiting for the recovery
attempt (i.e. the recovery will be attempted after at least
recovery_wait_time seconds).
If set to 1 (true), the time of the processed stream is taken into account
instead (i.e. the recovery will be attempted after at least @var{recovery_wait_time}
seconds of the stream is omitted).
By default, this option is set to 0 (false).

@item recover_any_error @var{bool}
If set to 1 (true), recovery will be attempted regardless of type of the error
causing the failure. By default this option is set to 0 (false) and in case of
certain (usually permanent) errors the recovery is not attempted even when
@var{attempt_recovery} is set to 1.

@item restart_with_keyframe @var{bool}
Specify whether to wait for the keyframe after recovering from
queue overflow or failure. This option is set to 0 (false) by default.

@end table

@subsection Examples

@itemize

@item
Stream something to rtmp server, continue processing the stream at real-time
rate even in case of temporary failure (network outage) and attempt to recover
streaming every second indefinitely.
@example
ffmpeg -re -i ... -c:v libx264 -c:a aac -f fifo -fifo_format flv -map 0:v -map 0:a
  -drop_pkts_on_overflow 1 -attempt_recovery 1 -recovery_wait_time 1 rtmp://example.com/live/stream_name
@end example

@end itemize

@anchor{tee}
@section tee

The tee muxer can be used to write the same data to several outputs, such as files or streams.
It can be used, for example, to stream a video over a network and save it to disk at the same time.

It is different from specifying several outputs to the @command{ffmpeg}
command-line tool. With the tee muxer, the audio and video data will be encoded only once.
With conventional multiple outputs, multiple encoding operations in parallel are initiated,
which can be a very expensive process. The tee muxer is not useful when using the libavformat API
directly because it is then possible to feed the same packets to several muxers directly.

Since the tee muxer does not represent any particular output format, ffmpeg cannot auto-select
output streams. So all streams intended for output must be specified using @code{-map}. See
the examples below.

Some encoders may need different options depending on the output format;
the auto-detection of this can not work with the tee muxer, so they need to be explicitly specified.
The main example is the @option{global_header} flag.

The slave outputs are specified in the file name given to the muxer,
separated by '|'. If any of the slave name contains the '|' separator,
leading or trailing spaces or any special character, those must be
escaped (see @ref{quoting_and_escaping,,the "Quoting and escaping"
section in the ffmpeg-utils(1) manual,ffmpeg-utils}).

@subsection Options

@table @option

@item use_fifo @var{bool}
If set to 1, slave outputs will be processed in separate threads using the @ref{fifo}
muxer. This allows to compensate for different speed/latency/reliability of
outputs and setup transparent recovery. By default this feature is turned off.

@item fifo_options
Options to pass to fifo pseudo-muxer instances. See @ref{fifo}.

@end table

Muxer options can be specified for each slave by prepending them as a list of
@var{key}=@var{value} pairs separated by ':', between square brackets. If
the options values contain a special character or the ':' separator, they
must be escaped; note that this is a second level escaping.

The following special options are also recognized:
@table @option
@item f
Specify the format name. Required if it cannot be guessed from the
output URL.

@item bsfs[/@var{spec}]
Specify a list of bitstream filters to apply to the specified
output.

It is possible to specify to which streams a given bitstream filter
applies, by appending a stream specifier to the option separated by
@code{/}. @var{spec} must be a stream specifier (see @ref{Format
stream specifiers}).

If the stream specifier is not specified, the bitstream filters will be
applied to all streams in the output. This will cause that output operation
to fail if the output contains streams to which the bitstream filter cannot
be applied e.g. @code{h264_mp4toannexb} being applied to an output containing an audio stream.

Options for a bitstream filter must be specified in the form of @code{opt=value}.

Several bitstream filters can be specified, separated by ",".

@item use_fifo @var{bool}
This allows to override tee muxer use_fifo option for individual slave muxer.

@item fifo_options
This allows to override tee muxer fifo_options for individual slave muxer.
See @ref{fifo}.

@item select
Select the streams that should be mapped to the slave output,
specified by a stream specifier. If not specified, this defaults to
all the mapped streams. This will cause that output operation to fail
if the output format does not accept all mapped streams.

You may use multiple stream specifiers separated by commas (@code{,}) e.g.: @code{a:0,v}

@item onfail
Specify behaviour on output failure. This can be set to either @code{abort} (which is
default) or @code{ignore}. @code{abort} will cause whole process to fail in case of failure
on this slave output. @code{ignore} will ignore failure on this output, so other outputs
will continue without being affected.
@end table

@subsection Examples

@itemize
@item
Encode something and both archive it in a WebM file and stream it
as MPEG-TS over UDP:
@example
ffmpeg -i ... -c:v libx264 -c:a mp2 -f tee -map 0:v -map 0:a
  "archive-20121107.mkv|[f=mpegts]udp://10.0.1.255:1234/"
@end example

@item
As above, but continue streaming even if output to local file fails
(for example local drive fills up):
@example
ffmpeg -i ... -c:v libx264 -c:a mp2 -f tee -map 0:v -map 0:a
  "[onfail=ignore]archive-20121107.mkv|[f=mpegts]udp://10.0.1.255:1234/"
@end example

@item
Use @command{ffmpeg} to encode the input, and send the output
to three different destinations. The @code{dump_extra} bitstream
filter is used to add extradata information to all the output video
keyframes packets, as requested by the MPEG-TS format. The select
option is applied to @file{out.aac} in order to make it contain only
audio packets.
@example
ffmpeg -i ... -map 0 -flags +global_header -c:v libx264 -c:a aac
       -f tee "[bsfs/v=dump_extra=freq=keyframe]out.ts|[movflags=+faststart]out.mp4|[select=a]out.aac"
@end example

@item
As above, but select only stream @code{a:1} for the audio output. Note
that a second level escaping must be performed, as ":" is a special
character used to separate options.
@example
ffmpeg -i ... -map 0 -flags +global_header -c:v libx264 -c:a aac
       -f tee "[bsfs/v=dump_extra=freq=keyframe]out.ts|[movflags=+faststart]out.mp4|[select=\'a:1\']out.aac"
@end example
@end itemize

@section webm_dash_manifest

WebM DASH Manifest muxer.

This muxer implements the WebM DASH Manifest specification to generate the DASH
manifest XML. It also supports manifest generation for DASH live streams.

For more information see:

@itemize @bullet
@item
WebM DASH Specification: @url{https://sites.google.com/a/webmproject.org/wiki/adaptive-streaming/webm-dash-specification}
@item
ISO DASH Specification: @url{http://standards.iso.org/ittf/PubliclyAvailableStandards/c065274_ISO_IEC_23009-1_2014.zip}
@end itemize

@subsection Options

This muxer supports the following options:

@table @option
@item adaptation_sets
This option has the following syntax: "id=x,streams=a,b,c id=y,streams=d,e" where x and y are the
unique identifiers of the adaptation sets and a,b,c,d and e are the indices of the corresponding
audio and video streams. Any number of adaptation sets can be added using this option.

@item live
Set this to 1 to create a live stream DASH Manifest. Default: 0.

@item chunk_start_index
Start index of the first chunk. This will go in the @samp{startNumber} attribute
of the @samp{SegmentTemplate} element in the manifest. Default: 0.

@item chunk_duration_ms
Duration of each chunk in milliseconds. This will go in the @samp{duration}
attribute of the @samp{SegmentTemplate} element in the manifest. Default: 1000.

@item utc_timing_url
URL of the page that will return the UTC timestamp in ISO format. This will go
in the @samp{value} attribute of the @samp{UTCTiming} element in the manifest.
Default: None.

@item time_shift_buffer_depth
Smallest time (in seconds) shifting buffer for which any Representation is
guaranteed to be available. This will go in the @samp{timeShiftBufferDepth}
attribute of the @samp{MPD} element. Default: 60.

@item minimum_update_period
Minimum update period (in seconds) of the manifest. This will go in the
@samp{minimumUpdatePeriod} attribute of the @samp{MPD} element. Default: 0.

@end table

@subsection Example
@example
ffmpeg -f webm_dash_manifest -i video1.webm \
       -f webm_dash_manifest -i video2.webm \
       -f webm_dash_manifest -i audio1.webm \
       -f webm_dash_manifest -i audio2.webm \
       -map 0 -map 1 -map 2 -map 3 \
       -c copy \
       -f webm_dash_manifest \
       -adaptation_sets "id=0,streams=0,1 id=1,streams=2,3" \
       manifest.xml
@end example

@section webm_chunk

WebM Live Chunk Muxer.

This muxer writes out WebM headers and chunks as separate files which can be
consumed by clients that support WebM Live streams via DASH.

@subsection Options

This muxer supports the following options:

@table @option
@item chunk_start_index
Index of the first chunk (defaults to 0).

@item header
Filename of the header where the initialization data will be written.

@item audio_chunk_duration
Duration of each audio chunk in milliseconds (defaults to 5000).
@end table

@subsection Example
@example
ffmpeg -f v4l2 -i /dev/video0 \
       -f alsa -i hw:0 \
       -map 0:0 \
       -c:v libvpx-vp9 \
       -s 640x360 -keyint_min 30 -g 30 \
       -f webm_chunk \
       -header webm_live_video_360.hdr \
       -chunk_start_index 1 \
       webm_live_video_360_%d.chk \
       -map 1:0 \
       -c:a libvorbis \
       -b:a 128k \
       -f webm_chunk \
       -header webm_live_audio_128.hdr \
       -chunk_start_index 1 \
       -audio_chunk_duration 1000 \
       webm_live_audio_128_%d.chk
@end example

@c man end MUXERS