Advanced Audio Coding (AAC) encoder.
-This encoder is the default AAC encoder, natively implemented into FFmpeg. Its
-quality is on par or better than libfdk_aac at the default bitrate of 128kbps.
-This encoder also implements more options, profiles and samplerates than
-other encoders (with only the AAC-HE profile pending to be implemented) so this
-encoder has become the default and is the recommended choice.
+This encoder is the default AAC encoder, natively implemented into FFmpeg.
@subsection Options
The @var{ac3} encoder uses floating-point math, while the @var{ac3_fixed}
encoder only uses fixed-point integer math. This does not mean that one is
always faster, just that one or the other may be better suited to a
-particular system. The floating-point encoder will generally produce better
-quality audio for a given bitrate. The @var{ac3_fixed} encoder is not the
-default codec for any of the output formats, so it must be specified explicitly
-using the option @code{-acodec ac3_fixed} in order to use it.
+particular system. The @var{ac3_fixed} encoder is not the default codec for
+any of the output formats, so it must be specified explicitly using the option
+@code{-acodec ac3_fixed} in order to use it.
@subsection AC-3 Metadata
so if you allow the use of GPL, you should configure with
@code{--enable-gpl --enable-nonfree --enable-libfdk-aac}.
-This encoder is considered to produce output on par or worse at 128kbps to the
-@ref{aacenc,,the native FFmpeg AAC encoder} but can often produce better
-sounding audio at identical or lower bitrates and has support for the
-AAC-HE profiles.
+This encoder has support for the AAC-HE profiles.
VBR encoding, enabled through the @option{vbr} or @option{flags
+qscale} options, is experimental and only works with some
Default value is 0.
+@item eld_v2
+Enable ELDv2 (LD-MPS extension for ELD stereo signals) for ELDv2 if set to 1,
+disabled if set to 0.
+
+Note that option is available when fdk-aac version (AACENCODER_LIB_VL0.AACENCODER_LIB_VL1.AACENCODER_LIB_VL2) > (4.0.0).
+
+Default value is 0.
+
@item signaling
Set SBR/PS signaling style.
@item packet_loss (@emph{expect-loss})
Set expected packet loss percentage. The default is 0.
+@item fec (@emph{n/a})
+Enable inband forward error correction. @option{packet_loss} must be non-zero
+to take advantage - frequency of FEC 'side-data' is proportional to expected packet loss.
+Default is disabled.
+
@item application (N.A.)
Set intended application type. Valid options are listed below:
@end table
-@anchor{libwavpack}
-@section libwavpack
-
-A wrapper providing WavPack encoding through libwavpack.
-
-Only lossless mode using 32-bit integer samples is supported currently.
-
-Requires the presence of the libwavpack headers and library during
-configuration. You need to explicitly configure the build with
-@code{--enable-libwavpack}.
-
-Note that a libavcodec-native encoder for the WavPack codec exists so users can
-encode audios with this codec without using this encoder. See @ref{wavpackenc}.
-
-@subsection Options
-
-@command{wavpack} command line utility's corresponding options are listed in
-parentheses, if any.
-
-@table @option
-@item frame_size (@emph{--blocksize})
-Default is 32768.
-
-@item compression_level
-Set speed vs. compression tradeoff. Acceptable arguments are listed below:
-
-@table @samp
-@item 0 (@emph{-f})
-Fast mode.
-
-@item 1
-Normal (default) settings.
-
-@item 2 (@emph{-h})
-High quality.
-
-@item 3 (@emph{-hh})
-Very high quality.
-
-@item 4-8 (@emph{-hh -x}@var{EXTRAPROC})
-Same as @samp{3}, but with extra processing enabled.
-
-@samp{4} is the same as @option{-x2} and @samp{8} is the same as @option{-x6}.
-
-@end table
-@end table
-
@anchor{mjpegenc}
@section mjpeg
WavPack lossless audio encoder.
-This is a libavcodec-native WavPack encoder. There is also an encoder based on
-libwavpack, but there is virtually no reason to use that encoder.
-
-See also @ref{libwavpack}.
-
@subsection Options
The equivalent options for @command{wavpack} command line utility are listed in
@file{libavcodec/wavpackenc.c}.
@item compression_level (@emph{-f}, @emph{-h}, @emph{-hh}, and @emph{-x})
-This option's syntax is consistent with @ref{libwavpack}'s.
@end table
@subsubsection Private options
A description of some of the currently available video encoders
follows.
+@section a64_multi, a64_multi5
+
+A64 / Commodore 64 multicolor charset encoder. @code{a64_multi5} is extended with 5th color (colram).
+
+@section GIF
+
+GIF image/animation encoder.
+
+@subsection Options
+
+@table @option
+@item gifflags @var{integer}
+Sets the flags used for GIF encoding.
+
+@table @option
+@item offsetting
+Enables picture offsetting.
+
+Default is enabled.
+
+@item transdiff
+Enables transparency detection between frames.
+
+Default is enabled.
+
+@end table
+
+@item gifimage @var{integer}
+Enables encoding one full GIF image per frame, rather than an animated GIF.
+
+Default value is @option{0}.
+
+@item global_palette @var{integer}
+Writes a palette to the global GIF header where feasible.
+
+If disabled, every frame will always have a palette written, even if there
+is a global palette supplied.
+
+Default value is @option{1}.
+
+@end table
+
@section Hap
Vidvox Hap video encoder.
@subsection Options
@table @option
-@item format
+@item format @var{integer}
Can be set to either @code{j2k} or @code{jp2} (the default) that
makes it possible to store non-rgb pix_fmts.
+@item tile_width @var{integer}
+Sets tile width. Range is 1 to 1073741824. Default is 256.
+
+@item tile_height @var{integer}
+Sets tile height. Range is 1 to 1073741824. Default is 256.
+
+@item pred @var{integer}
+Allows setting the discrete wavelet transform (DWT) type
+@table @option
+@item dwt97int (Lossy)
+@item dwt53 (Lossless)
+@end table
+Default is @code{dwt97int}
+
+@item sop @var{boolean}
+Enable this to add SOP marker at the start of each packet. Disabled by default.
+
+@item eph @var{boolean}
+Enable this to add EPH marker at the end of each packet header. Disabled by default.
+
+@item prog @var{integer}
+Sets the progression order to be used by the encoder.
+Possible values are:
+@table @option
+@item lrcp
+@item rlcp
+@item rpcl
+@item pcrl
+@item cprl
+@end table
+Set to @code{lrcp} by default.
+
+@item layer_rates @var{string}
+By default, when this option is not used, compression is done using the quality metric.
+This option allows for compression using compression ratio. The compression ratio for each
+level could be specified. The compression ratio of a layer @code{l} species the what ratio of
+total file size is contained in the first @code{l} layers.
+
+Example usage:
+
+@example
+ffmpeg -i input.bmp -c:v jpeg2000 -layer_rates "100,10,1" output.j2k
+@end example
+
+This would compress the image to contain 3 layers, where the data contained in the
+first layer would be compressed by 1000 times, compressed by 100 in the first two layers,
+and shall contain all data while using all 3 layers.
+
+@end table
+
+@section librav1e
+
+rav1e AV1 encoder wrapper.
+
+Requires the presence of the rav1e headers and library during configuration.
+You need to explicitly configure the build with @code{--enable-librav1e}.
+
+@subsection Options
+
+@table @option
+@item qmax
+Sets the maximum quantizer to use when using bitrate mode.
+
+@item qmin
+Sets the minimum quantizer to use when using bitrate mode.
+
+@item qp
+Uses quantizer mode to encode at the given quantizer (0-255).
+
+@item speed
+Selects the speed preset (0-10) to encode with.
+
+@item tiles
+Selects how many tiles to encode with.
+
+@item tile-rows
+Selects how many rows of tiles to encode with.
+
+@item tile-columns
+Selects how many columns of tiles to encode with.
+
+@item rav1e-params
+Set rav1e options using a list of @var{key}=@var{value} pairs separated
+by ":". See @command{rav1e --help} for a list of options.
+
+For example to specify librav1e encoding options with @option{-rav1e-params}:
+
+@example
+ffmpeg -i input -c:v librav1e -b:v 500K -rav1e-params speed=5:low_latency=true output.mp4
+@end example
+
@end table
@section libaom-av1
@item threads
Set the number of threads to use while encoding. This may require the
-@option{tiles} option to also be set to actually use the specified
-number of threads fully. Defaults to the number of hardware threads
-supported by the host machine.
+@option{tiles} or @option{row-mt} options to also be set to actually
+use the specified number of threads fully. Defaults to the number of
+hardware threads supported by the host machine.
@item profile
Set the encoding profile. Defaults to using the profile which matches
Enable use of alternate reference frames. Defaults to the internal
default of the library.
+@item arnr-max-frames (@emph{frames})
+Set altref noise reduction max frame count. Default is -1.
+
+@item arnr-strength (@emph{strength})
+Set altref noise reduction filter strength. Range is -1 to 6. Default is -1.
+
+@item aq-mode (@emph{aq-mode})
+Set adaptive quantization mode. Possible values:
+
+@table @samp
+@item none (@emph{0})
+Disabled.
+
+@item variance (@emph{1})
+Variance-based.
+
+@item complexity (@emph{2})
+Complexity-based.
+
+@item cyclic (@emph{3})
+Cyclic refresh.
+@end table
+
+@item tune (@emph{tune})
+Set the distortion metric the encoder is tuned with. Default is @code{psnr}.
+
+@table @samp
+@item psnr (@emph{0})
+
+@item ssim (@emph{1})
+@end table
+
@item lag-in-frames
Set the maximum number of frames which the encoder may keep in flight
at any one time for lookahead purposes. Defaults to the internal
has refilled above the threshold. Defaults to zero (no frames are
dropped).
+@item denoise-noise-level (@emph{level})
+Amount of noise to be removed for grain synthesis. Grain synthesis is disabled if
+this option is not set or set to 0.
+
+@item denoise-block-size (@emph{pixels})
+Block size used for denoising for grain synthesis. If not set, AV1 codec
+uses the default value of 32.
+
+@item undershoot-pct (@emph{pct})
+Set datarate undershoot (min) percentage of the target bitrate. Range is -1 to 100.
+Default is -1.
+
+@item overshoot-pct (@emph{pct})
+Set datarate overshoot (max) percentage of the target bitrate. Range is -1 to 1000.
+Default is -1.
+
+@item minsection-pct (@emph{pct})
+Minimum percentage variation of the GOP bitrate from the target bitrate. If minsection-pct
+is not set, the libaomenc wrapper computes it as follows: @code{(minrate * 100 / bitrate)}.
+Range is -1 to 100. Default is -1 (unset).
+
+@item maxsection-pct (@emph{pct})
+Maximum percentage variation of the GOP bitrate from the target bitrate. If maxsection-pct
+is not set, the libaomenc wrapper computes it as follows: @code{(maxrate * 100 / bitrate)}.
+Range is -1 to 5000. Default is -1 (unset).
+
+@item frame-parallel (@emph{boolean})
+Enable frame parallel decodability features. Default is true.
+
@item tiles
-Set the number of tiles to encode the input video with, as colums x
+Set the number of tiles to encode the input video with, as columns x
rows. Larger numbers allow greater parallelism in both encoding and
decoding, but may decrease coding efficiency. Defaults to the minimum
number of tiles required by the size of the input video (this is 1x1
Set the number of tiles as log2 of the number of tile rows and columns.
Provided for compatibility with libvpx/VP9.
+@item row-mt (Requires libaom >= 1.0.0-759-g90a15f4f2)
+Enable row based multi-threading. Disabled by default.
+
+@item enable-cdef (@emph{boolean})
+Enable Constrained Directional Enhancement Filter. The libaom-av1
+encoder enables CDEF by default.
+
+@item enable-restoration (@emph{boolean})
+Enable Loop Restoration Filter. Default is true for libaom-av1.
+
+@item enable-global-motion (@emph{boolean})
+Enable the use of global motion for block prediction. Default is true.
+
+@item enable-intrabc (@emph{boolean})
+Enable block copy mode for intra block prediction. This mode is
+useful for screen content. Default is true.
+
+@item enable-rect-partitions (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable rectangular partitions. Default is true.
+
+@item enable-1to4-partitions (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable 1:4/4:1 partitions. Default is true.
+
+@item enable-ab-partitions (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable AB shape partitions. Default is true.
+
+@item enable-angle-delta (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable angle delta intra prediction. Default is true.
+
+@item enable-cfl-intra (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable chroma predicted from luma intra prediction. Default is true.
+
+@item enable-filter-intra (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable filter intra predictor. Default is true.
+
+@item enable-intra-edge-filter (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable intra edge filter. Default is true.
+
+@item enable-smooth-intra (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable smooth intra prediction mode. Default is true.
+
+@item enable-paeth-intra (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable paeth predictor in intra prediction. Default is true.
+
+@item enable-palette (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable palette prediction mode. Default is true.
+
+@item enable-flip-idtx (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable extended transform type, including FLIPADST_DCT, DCT_FLIPADST,
+FLIPADST_FLIPADST, ADST_FLIPADST, FLIPADST_ADST, IDTX, V_DCT, H_DCT,
+V_ADST, H_ADST, V_FLIPADST, H_FLIPADST. Default is true.
+
+@item enable-tx64 (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable 64-pt transform. Default is true.
+
+@item reduced-tx-type-set (@emph{boolean}) (Requires libaom >= v2.0.0)
+Use reduced set of transform types. Default is false.
+
+@item use-intra-dct-only (@emph{boolean}) (Requires libaom >= v2.0.0)
+Use DCT only for INTRA modes. Default is false.
+
+@item use-inter-dct-only (@emph{boolean}) (Requires libaom >= v2.0.0)
+Use DCT only for INTER modes. Default is false.
+
+@item use-intra-default-tx-only (@emph{boolean}) (Requires libaom >= v2.0.0)
+Use Default-transform only for INTRA modes. Default is false.
+
+@item enable-ref-frame-mvs (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable temporal mv prediction. Default is true.
+
+@item enable-reduced-reference-set (@emph{boolean}) (Requires libaom >= v2.0.0)
+Use reduced set of single and compound references. Default is false.
+
+@item enable-obmc (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable obmc. Default is true.
+
+@item enable-dual-filter (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable dual filter. Default is true.
+
+@item enable-diff-wtd-comp (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable difference-weighted compound. Default is true.
+
+@item enable-dist-wtd-comp (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable distance-weighted compound. Default is true.
+
+@item enable-onesided-comp (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable one sided compound. Default is true.
+
+@item enable-interinter-wedge (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable interinter wedge compound. Default is true.
+
+@item enable-interintra-wedge (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable interintra wedge compound. Default is true.
+
+@item enable-masked-comp (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable masked compound. Default is true.
+
+@item enable-interintra-comp (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable interintra compound. Default is true.
+
+@item enable-smooth-interintra (@emph{boolean}) (Requires libaom >= v2.0.0)
+Enable smooth interintra mode. Default is true.
+
+@item aom-params
+Set libaom options using a list of @var{key}=@var{value} pairs separated
+by ":". For a list of supported options, see @command{aomenc --help} under the
+section "AV1 Specific Options".
+
+For example to specify libaom encoding options with @option{-aom-params}:
+
+@example
+ffmpeg -i input -c:v libaom-av1 -b:v 500K -aom-params tune=psnr:enable-tpl-model=1 output.mp4
+@end example
+
+@end table
+
+@section libsvtav1
+
+SVT-AV1 encoder wrapper.
+
+Requires the presence of the SVT-AV1 headers and library during configuration.
+You need to explicitly configure the build with @code{--enable-libsvtav1}.
+
+@subsection Options
+
+@table @option
+@item profile
+Set the encoding profile.
+
+@item level
+Set the operating point level.
+
+@item tier
+Set the operating point tier.
+
+@item rc
+Set the rate control mode to use.
+
+Possible modes:
+@table @option
+@item cqp
+Constant quantizer: use fixed values of qindex (dependent on the frame type)
+throughout the stream. This mode is the default.
+
+@item vbr
+Variable bitrate: use a target bitrate for the whole stream.
+
+@item cvbr
+Constrained variable bitrate: use a target bitrate for each GOP.
+@end table
+
+@item qmax
+Set the maximum quantizer to use when using a bitrate mode.
+
+@item qmin
+Set the minimum quantizer to use when using a bitrate mode.
+
+@item qp
+Set the quantizer used in cqp rate control mode (0-63).
+
+@item sc_detection
+Enable scene change detection.
+
+@item la_depth
+Set number of frames to look ahead (0-120).
+
+@item preset
+Set the quality-speed tradeoff, in the range 0 to 8. Higher values are
+faster but lower quality. Defaults to 8 (highest speed).
+
+@item tile_rows
+Set log2 of the number of rows of tiles to use (0-6).
+
+@item tile_columns
+Set log2 of the number of columns of tiles to use (0-4).
+
@end table
@section libkvazaar
@item auto-alt-ref
Enable use of alternate reference frames (2-pass only).
Values greater than 1 enable multi-layer alternate reference frames (VP9 only).
-@item arnr-max-frames
+@item arnr-maxframes
Set altref noise reduction max frame count.
@item arnr-type
Set altref noise reduction filter type: backward, forward, centered.
@item error-resilient
Enable error resiliency features.
-@item VP8-specific options
-@table @option
+@item sharpness @var{integer}
+Increase sharpness at the expense of lower PSNR.
+The valid range is [0, 7].
+
@item ts-parameters
Sets the temporal scalability configuration using a :-separated list of
key=value pairs. For example, to specify temporal scalability parameters
with @code{ffmpeg}:
@example
ffmpeg -i INPUT -c:v libvpx -ts-parameters ts_number_layers=3:\
-ts_target_bitrate=250000,500000,1000000:ts_rate_decimator=4,2,1:\
-ts_periodicity=4:ts_layer_id=0,2,1,2 OUTPUT
+ts_target_bitrate=250,500,1000:ts_rate_decimator=4,2,1:\
+ts_periodicity=4:ts_layer_id=0,2,1,2:ts_layering_mode=3 OUTPUT
@end example
Below is a brief explanation of each of the parameters, please
refer to @code{struct vpx_codec_enc_cfg} in @code{vpx/vpx_encoder.h} for more
@item ts_number_layers
Number of temporal coding layers.
@item ts_target_bitrate
-Target bitrate for each temporal layer.
+Target bitrate for each temporal layer (in kbps).
+(bitrate should be inclusive of the lower temporal layer).
@item ts_rate_decimator
Frame rate decimation factor for each temporal layer.
@item ts_periodicity
Length of the sequence defining frame temporal layer membership.
@item ts_layer_id
Template defining the membership of frames to temporal layers.
+@item ts_layering_mode
+(optional) Selecting the temporal structure from a set of pre-defined temporal layering modes.
+Currently supports the following options.
+@table @option
+@item 0
+No temporal layering flags are provided internally,
+relies on flags being passed in using @code{metadata} field in @code{AVFrame}
+with following keys.
+@table @option
+@item vp8-flags
+Sets the flags passed into the encoder to indicate the referencing scheme for
+the current frame.
+Refer to function @code{vpx_codec_encode} in @code{vpx/vpx_encoder.h} for more
+details.
+@item temporal_id
+Explicitly sets the temporal id of the current frame to encode.
+@end table
+@item 2
+Two temporal layers. 0-1...
+@item 3
+Three temporal layers. 0-2-1-2...; with single reference frame.
+@item 4
+Same as option "3", except there is a dependency between
+the two temporal layer 2 frames within the temporal period.
@end table
@end table
The valid range is [0, 10000]. 0 (default) uses standard VBR.
@item enable-tpl @var{boolean}
Enable temporal dependency model.
+@item ref-frame-config
+Using per-frame metadata, set members of the structure @code{vpx_svc_ref_frame_config_t} in @code{vpx/vp8cx.h} to fine-control referencing schemes and frame buffer management.
+@*Use a :-separated list of key=value pairs.
+For example,
+@example
+av_dict_set(&av_frame->metadata, "ref-frame-config", \
+"rfc_update_buffer_slot=7:rfc_lst_fb_idx=0:rfc_gld_fb_idx=1:rfc_alt_fb_idx=2:rfc_reference_last=0:rfc_reference_golden=0:rfc_reference_alt_ref=0");
+@end example
+@table @option
+@item rfc_update_buffer_slot
+Indicates the buffer slot number to update
+@item rfc_update_last
+Indicates whether to update the LAST frame
+@item rfc_update_golden
+Indicates whether to update GOLDEN frame
+@item rfc_update_alt_ref
+Indicates whether to update ALT_REF frame
+@item rfc_lst_fb_idx
+LAST frame buffer index
+@item rfc_gld_fb_idx
+GOLDEN frame buffer index
+@item rfc_alt_fb_idx
+ALT_REF frame buffer index
+@item rfc_reference_last
+Indicates whether to reference LAST frame
+@item rfc_reference_golden
+Indicates whether to reference GOLDEN frame
+@item rfc_reference_alt_ref
+Indicates whether to reference ALT_REF frame
+@item rfc_reference_duration
+Indicates frame duration
+@end table
@end table
@end table
@subsection Supported Pixel Formats
x264 supports 8- to 10-bit color spaces. The exact bit depth is controlled at
-x264's configure time. FFmpeg only supports one bit depth in one particular
-build. In other words, it is not possible to build one FFmpeg with multiple
-versions of x264 with different bit depths.
+x264's configure time.
@subsection Options
@subsection Options
@table @option
+@item b
+Sets target video bitrate.
+
+@item bf
+
+@item g
+Set the GOP size.
+
+@item keyint_min
+Minimum GOP size.
+
+@item refs
+Number of reference frames each P-frame can use. The range is from @var{1-16}.
+
@item preset
Set the x265 preset.
@item crf
Set the quality for constant quality mode.
+@item qp
+Set constant quantization rate control method parameter.
+
+@item qmin
+Minimum quantizer scale.
+
+@item qmax
+Maximum quantizer scale.
+
+@item qdiff
+Maximum difference between quantizer scales.
+
+@item qblur
+Quantizer curve blur
+
+@item qcomp
+Quantizer curve compression factor
+
+@item i_qfactor
+
+@item b_qfactor
+
@item forced-idr
Normally, when forcing a I-frame type, the encoder can select any type
of I-frame. This option forces it to choose an IDR-frame.
during configuration. You need to explicitly configure the build with
@option{--enable-libxavs2}.
+The following standard libavcodec options are used:
+@itemize
+@item
+@option{b} / @option{bit_rate}
+@item
+@option{g} / @option{gop_size}
+@item
+@option{bf} / @option{max_b_frames}
+@end itemize
+
+The encoder also has its own specific options:
@subsection Options
@table @option
For example to specify libxavs2 encoding options with @option{-xavs2-params}:
@example
-ffmpeg -i input -c:v libxavs2 -xavs2-params preset_level=5 output.avs2
+ffmpeg -i input -c:v libxavs2 -xavs2-params RdoqLevel=0 output.avs2
@end example
@end table
@end table
+@section MediaFoundation
+
+This provides wrappers to encoders (both audio and video) in the
+MediaFoundation framework. It can access both SW and HW encoders.
+Video encoders can take input in either of nv12 or yuv420p form
+(some encoders support both, some support only either - in practice,
+nv12 is the safer choice, especially among HW encoders).
+
@section mpeg2
MPEG-2 video encoder.
@subsection Options
@table @option
+@item profile
+Select the mpeg2 profile to encode:
+
+@table @samp
+@item 422
+@item high
+@item ss
+Spatially Scalable
+@item snr
+SNR Scalable
+@item main
+@item simple
+@end table
+
+@item level
+Select the mpeg2 level to encode:
+
+@table @samp
+@item high
+@item high1440
+@item main
+@item low
+@end table
+
@item seq_disp_ext @var{integer}
Specifies if the encoder should write a sequence_display_extension to the
output.
indicating the source of the video pictures. The default is @samp{unspecified},
can be @samp{component}, @samp{pal}, @samp{ntsc}, @samp{secam} or @samp{mac}.
For maximum compatibility, use @samp{component}.
+@item a53cc @var{boolean}
+Import closed captions (which must be ATSC compatible format) into output.
+Default is 1 (on).
@end table
@section png
@section QSV encoders
-The family of Intel QuickSync Video encoders (MPEG-2, H.264 and HEVC)
+The family of Intel QuickSync Video encoders (MPEG-2, H.264, HEVC, JPEG/MJPEG and VP9)
The ratecontrol method is selected as follows:
@end itemize
All encoders support the following options:
-@itemize
-@item
-@option{low_power}
-
+@table @option
+@item low_power
Some drivers/platforms offer a second encoder for some codecs intended to use
less power than the default encoder; setting this option will attempt to use
that encoder. Note that it may support a reduced feature set, so some other
options may not be available in this mode.
-@end itemize
+
+@item idr_interval
+Set the number of normal intra frames between full-refresh (IDR) frames in
+open-GOP mode. The intra frames are still IRAPs, but will not include global
+headers and may have non-decodable leading pictures.
+
+@item b_depth
+Set the B-frame reference depth. When set to one (the default), all B-frames
+will refer only to P- or I-frames. When set to greater values multiple layers
+of B-frames will be present, frames in each layer only referring to frames in
+higher layers.
+
+@item rc_mode
+Set the rate control mode to use. A given driver may only support a subset of
+modes.
+
+Possible modes:
+@table @option
+@item auto
+Choose the mode automatically based on driver support and the other options.
+This is the default.
+@item CQP
+Constant-quality.
+@item CBR
+Constant-bitrate.
+@item VBR
+Variable-bitrate.
+@item ICQ
+Intelligent constant-quality.
+@item QVBR
+Quality-defined variable-bitrate.
+@item AVBR
+Average variable bitrate.
+@end table
+
+@end table
Each encoder also has its own specific options:
@table @option
messages).
@end table
+@item tiles
+Set the number of tiles to encode the input video with, as columns x rows.
+Larger numbers allow greater parallelism in both encoding and decoding, but
+may decrease coding efficiency.
+
@end table
@item mjpeg_vaapi
@subsection Options
@table @option
+@item palette
+Specify the global palette used by the bitmaps.
+
+The format for this option is a string containing 16 24-bits hexadecimal
+numbers (without 0x prefix) separated by commas, for example @code{0d00ee,
+ee450d, 101010, eaeaea, 0ce60b, ec14ed, ebff0b, 0d617a, 7b7b7b, d1d1d1,
+7b2a0e, 0d950c, 0f007b, cf0dec, cfa80c, 7c127b}.
+
@item even_rows_fix
When set to 1, enable a work-around that makes the number of pixel rows
even in all subtitles. This fixes a problem with some players that
projects / ffmpeg / blobdiff