Default value is 0.
+@item eld_v2
+Enable ELDv2 (LD-MPS extension for ELD stereo signals) for ELDv2 if set to 1,
+disabled if set to 0.
+
+Note that option is available when fdk-aac version (AACENCODER_LIB_VL0.AACENCODER_LIB_VL1.AACENCODER_LIB_VL2) > (4.0.0).
+
+Default value is 0.
+
@item signaling
Set SBR/PS signaling style.
@end table
+@section libaom-av1
+
+libaom AV1 encoder wrapper.
+
+Requires the presence of the libaom headers and library during
+configuration. You need to explicitly configure the build with
+@code{--enable-libaom}.
+
+@subsection Options
+
+The wrapper supports the following standard libavcodec options:
+
+@table @option
+
+@item b
+Set bitrate target in bits/second. By default this will use
+variable-bitrate mode. If @option{maxrate} and @option{minrate} are
+also set to the same value then it will use constant-bitrate mode,
+otherwise if @option{crf} is set as well then it will use
+constrained-quality mode.
+
+@item g keyint_min
+Set key frame placement. The GOP size sets the maximum distance between
+key frames; if zero the output stream will be intra-only. The minimum
+distance is ignored unless it is the same as the GOP size, in which case
+key frames will always appear at a fixed interval. Not set by default,
+so without this option the library has completely free choice about
+where to place key frames.
+
+@item qmin qmax
+Set minimum/maximum quantisation values. Valid range is from 0 to 63
+(warning: this does not match the quantiser values actually used by AV1
+- divide by four to map real quantiser values to this range). Defaults
+to min/max (no constraint).
+
+@item minrate maxrate bufsize rc_init_occupancy
+Set rate control buffering parameters. Not used if not set - defaults
+to unconstrained variable bitrate.
+
+@item threads
+Set the number of threads to use while encoding. This may require the
+@option{tiles} or @option{row-mt} options to also be set to actually
+use the specified number of threads fully. Defaults to the number of
+hardware threads supported by the host machine.
+
+@item profile
+Set the encoding profile. Defaults to using the profile which matches
+the bit depth and chroma subsampling of the input.
+
+@end table
+
+The wrapper also has some specific options:
+
+@table @option
+
+@item cpu-used
+Set the quality/encoding speed tradeoff. Valid range is from 0 to 8,
+higher numbers indicating greater speed and lower quality. The default
+value is 1, which will be slow and high quality.
+
+@item auto-alt-ref
+Enable use of alternate reference frames. Defaults to the internal
+default of the library.
+
+@item arnr-max-frames (@emph{frames})
+Set altref noise reduction max frame count. Default is -1.
+
+@item arnr-strength (@emph{strength})
+Set altref noise reduction filter strength. Range is -1 to 6. Default is -1.
+
+@item aq-mode (@emph{aq-mode})
+Set adaptive quantization mode. Possible values:
+
+@table @samp
+@item none (@emph{0})
+Disabled.
+
+@item variance (@emph{1})
+Variance-based.
+
+@item complexity (@emph{2})
+Complexity-based.
+
+@item cyclic (@emph{3})
+Cyclic refresh.
+@end table
+
+@item lag-in-frames
+Set the maximum number of frames which the encoder may keep in flight
+at any one time for lookahead purposes. Defaults to the internal
+default of the library.
+
+@item error-resilience
+Enable error resilience features:
+@table @option
+@item default
+Improve resilience against losses of whole frames.
+@end table
+Not enabled by default.
+
+@item crf
+Set the quality/size tradeoff for constant-quality (no bitrate target)
+and constrained-quality (with maximum bitrate target) modes. Valid
+range is 0 to 63, higher numbers indicating lower quality and smaller
+output size. Only used if set; by default only the bitrate target is
+used.
+
+@item static-thresh
+Set a change threshold on blocks below which they will be skipped by
+the encoder. Defined in arbitrary units as a nonnegative integer,
+defaulting to zero (no blocks are skipped).
+
+@item drop-threshold
+Set a threshold for dropping frames when close to rate control bounds.
+Defined as a percentage of the target buffer - when the rate control
+buffer falls below this percentage, frames will be dropped until it
+has refilled above the threshold. Defaults to zero (no frames are
+dropped).
+
+@item denoise-noise-level (@emph{level})
+Amount of noise to be removed for grain synthesis. Grain synthesis is disabled if
+this option is not set or set to 0.
+
+@item denoise-block-size (@emph{pixels})
+Block size used for denoising for grain synthesis. If not set, AV1 codec
+uses the default value of 32.
+
+@item undershoot-pct (@emph{pct})
+Set datarate undershoot (min) percentage of the target bitrate. Range is -1 to 100.
+Default is -1.
+
+@item overshoot-pct (@emph{pct})
+Set datarate overshoot (max) percentage of the target bitrate. Range is -1 to 1000.
+Default is -1.
+
+@item minsection-pct (@emph{pct})
+Minimum percentage variation of the GOP bitrate from the target bitrate. If minsection-pct
+is not set, the libaomenc wrapper computes it as follows: @code{(minrate * 100 / bitrate)}.
+Range is -1 to 100. Default is -1 (unset).
+
+@item maxsection-pct (@emph{pct})
+Maximum percentage variation of the GOP bitrate from the target bitrate. If maxsection-pct
+is not set, the libaomenc wrapper computes it as follows: @code{(maxrate * 100 / bitrate)}.
+Range is -1 to 5000. Default is -1 (unset).
+
+@item frame-parallel (@emph{boolean})
+Enable frame parallel decodability features. Default is true.
+
+@item tiles
+Set the number of tiles to encode the input video with, as columns x
+rows. Larger numbers allow greater parallelism in both encoding and
+decoding, but may decrease coding efficiency. Defaults to the minimum
+number of tiles required by the size of the input video (this is 1x1
+(that is, a single tile) for sizes up to and including 4K).
+
+@item tile-columns tile-rows
+Set the number of tiles as log2 of the number of tile rows and columns.
+Provided for compatibility with libvpx/VP9.
+
+@item row-mt (Requires libaom >= 1.0.0-759-g90a15f4f2)
+Enable row based multi-threading. Disabled by default.
+
+@item enable-cdef (@emph{boolean})
+Enable Constrained Directional Enhancement Filter. The libaom-av1
+encoder enables CDEF by default.
+
+@item enable-global-motion (@emph{boolean})
+Enable the use of global motion for block prediction. Default is true.
+
+@item enable-intrabc (@emph{boolean})
+Enable block copy mode for intra block prediction. This mode is
+useful for screen content. Default is true.
+
+@end table
+
@section libkvazaar
Kvazaar H.265/HEVC encoder.
@table @option
@item auto-alt-ref
Enable use of alternate reference frames (2-pass only).
-@item arnr-max-frames
+Values greater than 1 enable multi-layer alternate reference frames (VP9 only).
+@item arnr-maxframes
Set altref noise reduction max frame count.
@item arnr-type
Set altref noise reduction filter type: backward, forward, centered.
@item error-resilient
Enable error resiliency features.
+@item sharpness @var{integer}
+Increase sharpness at the expense of lower PSNR.
+The valid range is [0, 7].
+
+@item VP8-specific options
+@table @option
+@item ts-parameters
+Sets the temporal scalability configuration using a :-separated list of
+key=value pairs. For example, to specify temporal scalability parameters
+with @code{ffmpeg}:
+@example
+ffmpeg -i INPUT -c:v libvpx -ts-parameters ts_number_layers=3:\
+ts_target_bitrate=250000,500000,1000000:ts_rate_decimator=4,2,1:\
+ts_periodicity=4:ts_layer_id=0,2,1,2 OUTPUT
+@end example
+Below is a brief explanation of each of the parameters, please
+refer to @code{struct vpx_codec_enc_cfg} in @code{vpx/vpx_encoder.h} for more
+details.
+@table @option
+@item ts_number_layers
+Number of temporal coding layers.
+@item ts_target_bitrate
+Target bitrate for each temporal layer.
+@item ts_rate_decimator
+Frame rate decimation factor for each temporal layer.
+@item ts_periodicity
+Length of the sequence defining frame temporal layer membership.
+@item ts_layer_id
+Template defining the membership of frames to temporal layers.
+@end table
+@end table
+
@item VP9-specific options
@table @option
@item lossless
midpoint is passed in rather than calculated for a specific clip or chunk.
The valid range is [0, 10000]. 0 (default) uses standard VBR.
+@item enable-tpl @var{boolean}
+Enable temporal dependency model.
@end table
@end table
@end example
@end table
+@section libxavs2
+
+xavs2 AVS2-P2/IEEE1857.4 encoder wrapper.
+
+This encoder requires the presence of the libxavs2 headers and library
+during configuration. You need to explicitly configure the build with
+@option{--enable-libxavs2}.
+
+The following standard libavcodec options are used:
+@itemize
+@item
+@option{b} / @option{bit_rate}
+@item
+@option{g} / @option{gop_size}
+@item
+@option{bf} / @option{max_b_frames}
+@end itemize
+
+The encoder also has its own specific options:
+@subsection Options
+
+@table @option
+@item lcu_row_threads
+Set the number of parallel threads for rows from 1 to 8 (default 5).
+
+@item initial_qp
+Set the xavs2 quantization parameter from 1 to 63 (default 34). This is
+used to set the initial qp for the first frame.
+
+@item qp
+Set the xavs2 quantization parameter from 1 to 63 (default 34). This is
+used to set the qp value under constant-QP mode.
+
+@item max_qp
+Set the max qp for rate control from 1 to 63 (default 55).
+
+@item min_qp
+Set the min qp for rate control from 1 to 63 (default 20).
+
+@item speed_level
+Set the Speed level from 0 to 9 (default 0). Higher is better but slower.
+
+@item log_level
+Set the log level from -1 to 3 (default 0). -1: none, 0: error,
+1: warning, 2: info, 3: debug.
+
+@item xavs2-params
+Set xavs2 options using a list of @var{key}=@var{value} couples separated
+by ":".
+
+For example to specify libxavs2 encoding options with @option{-xavs2-params}:
+
+@example
+ffmpeg -i input -c:v libxavs2 -xavs2-params RdoqLevel=0 output.avs2
+@end example
+@end table
+
@section libxvid
Xvid MPEG-4 Part 2 encoder wrapper.
indicating the source of the video pictures. The default is @samp{unspecified},
can be @samp{component}, @samp{pal}, @samp{ntsc}, @samp{secam} or @samp{mac}.
For maximum compatibility, use @samp{component}.
+@item a53cc @var{boolean}
+Import closed captions (which must be ATSC compatible format) into output.
+Default is 1 (on).
@end table
@section png
@option{b_qfactor} / @option{b_quant_factor}
@item
@option{b_qoffset} / @option{b_quant_offset}
+@item
+@option{slices}
@end itemize
All encoders support the following options:
-@itemize
-@item
-@option{low_power}
-
+@table @option
+@item low_power
Some drivers/platforms offer a second encoder for some codecs intended to use
less power than the default encoder; setting this option will attempt to use
that encoder. Note that it may support a reduced feature set, so some other
options may not be available in this mode.
-@end itemize
+
+@item idr_interval
+Set the number of normal intra frames between full-refresh (IDR) frames in
+open-GOP mode. The intra frames are still IRAPs, but will not include global
+headers and may have non-decodable leading pictures.
+
+@item b_depth
+Set the B-frame reference depth. When set to one (the default), all B-frames
+will refer only to P- or I-frames. When set to greater values multiple layers
+of B-frames will be present, frames in each layer only referring to frames in
+higher layers.
+
+@item rc_mode
+Set the rate control mode to use. A given driver may only support a subset of
+modes.
+
+Possible modes:
+@table @option
+@item auto
+Choose the mode automatically based on driver support and the other options.
+This is the default.
+@item CQP
+Constant-quality.
+@item CBR
+Constant-bitrate.
+@item VBR
+Variable-bitrate.
+@item ICQ
+Intelligent constant-quality.
+@item QVBR
+Quality-defined variable-bitrate.
+@item AVBR
+Average variable bitrate.
+@end table
+
+@end table
Each encoder also has its own specific options:
@table @option
Set @emph{general_tier_flag}. This may affect the level chosen for the stream
if it is not explicitly specified.
+@item sei
+Set SEI message types to include.
+Some combination of the following values:
+@table @samp
+@item hdr
+Include HDR metadata if the input frames have it
+(@emph{mastering_display_colour_volume} and @emph{content_light_level}
+messages).
+@end table
+
@end table
@item mjpeg_vaapi
@end table
-@section libxavs2
-
-xavs2 AVS2-P2/IEEE1857.4 encoder wrapper.
-
-This encoder requires the presence of the libxavs2 headers and library
-during configuration. You need to explicitly configure the build with
-@option{--enable-libxavs2}.
-
-@subsection Options
-
-@table @option
-@item lcu_row_threads
-Set the number of parallel threads for rows from 1 to 8 (default 5).
-
-@item initial_qp
-Set the xavs2 quantization parameter from 1 to 63 (default 34). This is
-used to set the initial qp for the first frame.
-
-@item qp
-Set the xavs2 quantization parameter from 1 to 63 (default 34). This is
-used to set the qp value under constant-QP mode.
-
-@item max_qp
-Set the max qp for rate control from 1 to 63 (default 55).
-
-@item min_qp
-Set the min qp for rate control from 1 to 63 (default 20).
-
-@item speed_level
-Set the Speed level from 0 to 9 (default 0). Higher is better but slower.
-
-@item log_level
-Set the log level from -1 to 3 (default 0). -1: none, 0: error,
-1: warning, 2: info, 3: debug.
-
-@item xavs2-params
-Set xavs2 options using a list of @var{key}=@var{value} couples separated
-by ":".
-
-For example to specify libxavs2 encoding options with @option{-xavs2-params}:
-
-@example
-ffmpeg -i input -c:v libxavs2 -xavs2-params preset_level=5 output.avs2
-@end example
-@end table
-
@c man end VIDEO ENCODERS
@chapter Subtitles Encoders
projects / ffmpeg / blobdiff