A filter with no input pads is called a "source", a filter with no
output pads is called a "sink".
+@anchor{Filtergraph syntax}
@section Filtergraph syntax
-A filtergraph can be represented using a textual representation, which
-is recognized by the @code{-vf} and @code{-af} options of the ff*
-tools, and by the @code{av_parse_graph()} function defined in
-@file{libavfilter/avfiltergraph}.
+A filtergraph can be represented using a textual representation, which is
+recognized by the @option{-filter}/@option{-vf} and @option{-filter_complex}
+options in @command{avconv} and @option{-vf} in @command{avplay}, and by the
+@code{avfilter_graph_parse()}/@code{avfilter_graph_parse2()} function defined in
+@file{libavfilter/avfiltergraph.h}.
A filterchain consists of a sequence of connected filters, each one
connected to the previous one in the sequence. A filterchain is
pads must be connected. A filtergraph is considered valid if all the
filter input and output pads of all the filterchains are connected.
+Libavfilter will automatically insert scale filters where format
+conversion is required. It is possible to specify swscale flags
+for those automatically inserted scalers by prepending
+@code{sws_flags=@var{flags};}
+to the filtergraph description.
+
Follows a BNF description for the filtergraph syntax:
@example
@var{NAME} ::= sequence of alphanumeric characters and '_'
@var{FILTER_ARGUMENTS} ::= sequence of chars (eventually quoted)
@var{FILTER} ::= [@var{LINKNAMES}] @var{NAME} ["=" @var{ARGUMENTS}] [@var{LINKNAMES}]
@var{FILTERCHAIN} ::= @var{FILTER} [,@var{FILTERCHAIN}]
-@var{FILTERGRAPH} ::= @var{FILTERCHAIN} [;@var{FILTERGRAPH}]
+@var{FILTERGRAPH} ::= [sws_flags=@var{flags};] @var{FILTERCHAIN} [;@var{FILTERGRAPH}]
@end example
@c man end FILTERGRAPH DESCRIPTION
@chapter Audio Filters
@c man begin AUDIO FILTERS
-When you configure your FFmpeg build, you can disable any of the
+When you configure your Libav build, you can disable any of the
existing filters using --disable-filters.
The configure output will show the audio filters included in your
build.
Below is a description of the currently available audio filters.
+@section aformat
+
+Convert the input audio to one of the specified formats. The framework will
+negotiate the most appropriate format to minimize conversions.
+
+The filter accepts the following named parameters:
+@table @option
+
+@item sample_fmts
+A comma-separated list of requested sample formats.
+
+@item sample_rates
+A comma-separated list of requested sample rates.
+
+@item channel_layouts
+A comma-separated list of requested channel layouts.
+
+@end table
+
+If a parameter is omitted, all values are allowed.
+
+For example to force the output to either unsigned 8-bit or signed 16-bit stereo:
+@example
+aformat=sample_fmts\=u8\,s16:channel_layouts\=stereo
+@end example
+
+@section amix
+
+Mixes multiple audio inputs into a single output.
+
+For example
+@example
+avconv -i INPUT1 -i INPUT2 -i INPUT3 -filter_complex amix=inputs=3:duration=first:dropout_transition=3 OUTPUT
+@end example
+will mix 3 input audio streams to a single output with the same duration as the
+first input and a dropout transition time of 3 seconds.
+
+The filter accepts the following named parameters:
+@table @option
+
+@item inputs
+Number of inputs. If unspecified, it defaults to 2.
+
+@item duration
+How to determine the end-of-stream.
+@table @option
+
+@item longest
+Duration of longest input. (default)
+
+@item shortest
+Duration of shortest input.
+
+@item first
+Duration of first input.
+
+@end table
+
+@item dropout_transition
+Transition time, in seconds, for volume renormalization when an input
+stream ends. The default value is 2 seconds.
+
+@end table
+
@section anull
Pass the audio source unchanged to the output.
+@section ashowinfo
+
+Show a line containing various information for each input audio frame.
+The input audio is not modified.
+
+The shown line contains a sequence of key/value pairs of the form
+@var{key}:@var{value}.
+
+A description of each shown parameter follows:
+
+@table @option
+@item n
+sequential number of the input frame, starting from 0
+
+@item pts
+Presentation timestamp of the input frame, in time base units; the time base
+depends on the filter input pad, and is usually 1/@var{sample_rate}.
+
+@item pts_time
+presentation timestamp of the input frame in seconds
+
+@item fmt
+sample format
+
+@item chlayout
+channel layout
+
+@item rate
+sample rate for the audio frame
+
+@item nb_samples
+number of samples (per channel) in the frame
+
+@item checksum
+Adler-32 checksum (printed in hexadecimal) of the audio data. For planar audio
+the data is treated as if all the planes were concatenated.
+
+@item plane_checksums
+A list of Adler-32 checksums for each data plane.
+@end table
+
+@section asplit
+
+Split input audio into several identical outputs.
+
+The filter accepts a single parameter which specifies the number of outputs. If
+unspecified, it defaults to 2.
+
+For example
+@example
+avconv -i INPUT -filter_complex asplit=5 OUTPUT
+@end example
+will create 5 copies of the input audio.
+
+@section asyncts
+Synchronize audio data with timestamps by squeezing/stretching it and/or
+dropping samples/adding silence when needed.
+
+The filter accepts the following named parameters:
+@table @option
+
+@item compensate
+Enable stretching/squeezing the data to make it match the timestamps. Disabled
+by default. When disabled, time gaps are covered with silence.
+
+@item min_delta
+Minimum difference between timestamps and audio data (in seconds) to trigger
+adding/dropping samples. Default value is 0.1. If you get non-perfect sync with
+this filter, try setting this parameter to 0.
+
+@item max_comp
+Maximum compensation in samples per second. Relevant only with compensate=1.
+Default value 500.
+
+@item first_pts
+Assume the first pts should be this value. The time base is 1 / sample rate.
+This allows for padding/trimming at the start of stream. By default, no
+assumption is made about the first frame's expected pts, so no padding or
+trimming is done. For example, this could be set to 0 to pad the beginning with
+silence if an audio stream starts after the video stream or to trim any samples
+with a negative pts due to encoder delay.
+
+@end table
+
+@section channelsplit
+Split each channel in input audio stream into a separate output stream.
+
+This filter accepts the following named parameters:
+@table @option
+@item channel_layout
+Channel layout of the input stream. Default is "stereo".
+@end table
+
+For example, assuming a stereo input MP3 file
+@example
+avconv -i in.mp3 -filter_complex channelsplit out.mkv
+@end example
+will create an output Matroska file with two audio streams, one containing only
+the left channel and the other the right channel.
+
+To split a 5.1 WAV file into per-channel files
+@example
+avconv -i in.wav -filter_complex
+'channelsplit=channel_layout=5.1[FL][FR][FC][LFE][SL][SR]'
+-map '[FL]' front_left.wav -map '[FR]' front_right.wav -map '[FC]'
+front_center.wav -map '[LFE]' lfe.wav -map '[SL]' side_left.wav -map '[SR]'
+side_right.wav
+@end example
+
+@section channelmap
+Remap input channels to new locations.
+
+This filter accepts the following named parameters:
+@table @option
+@item channel_layout
+Channel layout of the output stream.
+
+@item map
+Map channels from input to output. The argument is a comma-separated list of
+mappings, each in the @code{@var{in_channel}-@var{out_channel}} or
+@var{in_channel} form. @var{in_channel} can be either the name of the input
+channel (e.g. FL for front left) or its index in the input channel layout.
+@var{out_channel} is the name of the output channel or its index in the output
+channel layout. If @var{out_channel} is not given then it is implicitly an
+index, starting with zero and increasing by one for each mapping.
+@end table
+
+If no mapping is present, the filter will implicitly map input channels to
+output channels preserving index.
+
+For example, assuming a 5.1+downmix input MOV file
+@example
+avconv -i in.mov -filter 'channelmap=map=DL-FL\,DR-FR' out.wav
+@end example
+will create an output WAV file tagged as stereo from the downmix channels of
+the input.
+
+To fix a 5.1 WAV improperly encoded in AAC's native channel order
+@example
+avconv -i in.wav -filter 'channelmap=1\,2\,0\,5\,3\,4:channel_layout=5.1' out.wav
+@end example
+
+@section join
+Join multiple input streams into one multi-channel stream.
+
+The filter accepts the following named parameters:
+@table @option
+
+@item inputs
+Number of input streams. Defaults to 2.
+
+@item channel_layout
+Desired output channel layout. Defaults to stereo.
+
+@item map
+Map channels from inputs to output. The argument is a comma-separated list of
+mappings, each in the @code{@var{input_idx}.@var{in_channel}-@var{out_channel}}
+form. @var{input_idx} is the 0-based index of the input stream. @var{in_channel}
+can be either the name of the input channel (e.g. FL for front left) or its
+index in the specified input stream. @var{out_channel} is the name of the output
+channel.
+@end table
+
+The filter will attempt to guess the mappings when those are not specified
+explicitly. It does so by first trying to find an unused matching input channel
+and if that fails it picks the first unused input channel.
+
+E.g. to join 3 inputs (with properly set channel layouts)
+@example
+avconv -i INPUT1 -i INPUT2 -i INPUT3 -filter_complex join=inputs=3 OUTPUT
+@end example
+
+To build a 5.1 output from 6 single-channel streams:
+@example
+avconv -i fl -i fr -i fc -i sl -i sr -i lfe -filter_complex
+'join=inputs=6:channel_layout=5.1:map=0.0-FL\,1.0-FR\,2.0-FC\,3.0-SL\,4.0-SR\,5.0-LFE'
+out
+@end example
+
+@section resample
+Convert the audio sample format, sample rate and channel layout. This filter is
+not meant to be used directly, it is inserted automatically by libavfilter
+whenever conversion is needed. Use the @var{aformat} filter to force a specific
+conversion.
+
+@section volume
+
+Adjust the input audio volume.
+
+The filter accepts the following named parameters:
+@table @option
+
+@item volume
+Expresses how the audio volume will be increased or decreased.
+
+Output values are clipped to the maximum value.
+
+The output audio volume is given by the relation:
+@example
+@var{output_volume} = @var{volume} * @var{input_volume}
+@end example
+
+Default value for @var{volume} is 1.0.
+
+@item precision
+Mathematical precision.
+
+This determines which input sample formats will be allowed, which affects the
+precision of the volume scaling.
+
+@table @option
+@item fixed
+8-bit fixed-point; limits input sample format to U8, S16, and S32.
+@item float
+32-bit floating-point; limits input sample format to FLT. (default)
+@item double
+64-bit floating-point; limits input sample format to DBL.
+@end table
+@end table
+
+@subsection Examples
+
+@itemize
+@item
+Halve the input audio volume:
+@example
+volume=volume=0.5
+volume=volume=1/2
+volume=volume=-6.0206dB
+@end example
+
+@item
+Increase input audio power by 6 decibels using fixed-point precision:
+@example
+volume=volume=6dB:precision=fixed
+@end example
+@end itemize
+
@c man end AUDIO FILTERS
@chapter Audio Sources
of @var{channel_layout} is 3, which corresponds to CH_LAYOUT_STEREO.
Check the channel_layout_map definition in
-@file{libavcodec/audioconvert.c} for the mapping between strings and
+@file{libavutil/channel_layout.c} for the mapping between strings and
channel layout values.
Follow some examples:
anullsrc=48000:mono
@end example
+@section abuffer
+Buffer audio frames, and make them available to the filter chain.
+
+This source is not intended to be part of user-supplied graph descriptions but
+for insertion by calling programs through the interface defined in
+@file{libavfilter/buffersrc.h}.
+
+It accepts the following named parameters:
+@table @option
+
+@item time_base
+Timebase which will be used for timestamps of submitted frames. It must be
+either a floating-point number or in @var{numerator}/@var{denominator} form.
+
+@item sample_rate
+Audio sample rate.
+
+@item sample_fmt
+Name of the sample format, as returned by @code{av_get_sample_fmt_name()}.
+
+@item channel_layout
+Channel layout of the audio data, in the form that can be accepted by
+@code{av_get_channel_layout()}.
+@end table
+
+All the parameters need to be explicitly defined.
+
@c man end AUDIO SOURCES
@chapter Audio Sinks
mainly useful as a template and to be employed in analysis / debugging
tools.
+@section abuffersink
+This sink is intended for programmatic use. Frames that arrive on this sink can
+be retrieved by the calling program using the interface defined in
+@file{libavfilter/buffersink.h}.
+
+This filter accepts no parameters.
+
@c man end AUDIO SINKS
@chapter Video Filters
@c man begin VIDEO FILTERS
-When you configure your FFmpeg build, you can disable any of the
+When you configure your Libav build, you can disable any of the
existing filters using --disable-filters.
The configure output will show the video filters included in your
build.
@var{threshold} is the threshold below which a pixel value is
considered black, and defaults to 32.
+@section boxblur
+
+Apply boxblur algorithm to the input video.
+
+This filter accepts the parameters:
+@var{luma_power}:@var{luma_radius}:@var{chroma_radius}:@var{chroma_power}:@var{alpha_radius}:@var{alpha_power}
+
+Chroma and alpha parameters are optional, if not specified they default
+to the corresponding values set for @var{luma_radius} and
+@var{luma_power}.
+
+@var{luma_radius}, @var{chroma_radius}, and @var{alpha_radius} represent
+the radius in pixels of the box used for blurring the corresponding
+input plane. They are expressions, and can contain the following
+constants:
+@table @option
+@item w, h
+the input width and height in pixels
+
+@item cw, ch
+the input chroma image width and height in pixels
+
+@item hsub, vsub
+horizontal and vertical chroma subsample values. For example for the
+pixel format "yuv422p" @var{hsub} is 2 and @var{vsub} is 1.
+@end table
+
+The radius must be a non-negative number, and must not be greater than
+the value of the expression @code{min(w,h)/2} for the luma and alpha planes,
+and of @code{min(cw,ch)/2} for the chroma planes.
+
+@var{luma_power}, @var{chroma_power}, and @var{alpha_power} represent
+how many times the boxblur filter is applied to the corresponding
+plane.
+
+Some examples follow:
+
+@itemize
+
+@item
+Apply a boxblur filter with luma, chroma, and alpha radius
+set to 2:
+@example
+boxblur=2:1
+@end example
+
+@item
+Set luma radius to 2, alpha and chroma radius to 0
+@example
+boxblur=2:1:0:0:0:0
+@end example
+
+@item
+Set luma and chroma radius to a fraction of the video dimension
+@example
+boxblur=min(h\,w)/10:1:min(cw\,ch)/10:1
+@end example
+
+@end itemize
+
@section copy
Copy the input source unchanged to the output. Mainly useful for
each new frame.
@item in_w, in_h
-the input width and heigth
+the input width and height
@item iw, ih
same as @var{in_w} and @var{in_h}
@item out_w, out_h
-the output (cropped) width and heigth
+the output (cropped) width and height
@item ow, oh
same as @var{out_w} and @var{out_h}
playback.
@end table
+@section delogo
+
+Suppress a TV station logo by a simple interpolation of the surrounding
+pixels. Just set a rectangle covering the logo and watch it disappear
+(and sometimes something even uglier appear - your mileage may vary).
+
+The filter accepts parameters as a string of the form
+"@var{x}:@var{y}:@var{w}:@var{h}:@var{band}", or as a list of
+@var{key}=@var{value} pairs, separated by ":".
+
+The description of the accepted parameters follows.
+
+@table @option
+
+@item x, y
+Specify the top left corner coordinates of the logo. They must be
+specified.
+
+@item w, h
+Specify the width and height of the logo to clear. They must be
+specified.
+
+@item band, t
+Specify the thickness of the fuzzy edge of the rectangle (added to
+@var{w} and @var{h}). The default value is 4.
+
+@item show
+When set to 1, a green rectangle is drawn on the screen to simplify
+finding the right @var{x}, @var{y}, @var{w}, @var{h} parameters, and
+@var{band} is set to 4. The default value is 0.
+
+@end table
+
+Some examples follow.
+
+@itemize
+
+@item
+Set a rectangle covering the area with top left corner coordinates 0,0
+and size 100x77, setting a band of size 10:
+@example
+delogo=0:0:100:77:10
+@end example
+
+@item
+As the previous example, but use named options:
+@example
+delogo=x=0:y=0:w=100:h=77:band=10
+@end example
+
+@end itemize
+
@section drawbox
Draw a colored box on the input image.
(case insensitive match) or a 0xRRGGBB[AA] sequence.
@end table
-Follow some examples:
+Follow some examples:
+@example
+# draw a black box around the edge of the input image
+drawbox
+
+# draw a box with color red and an opacity of 50%
+drawbox=10:20:200:60:red@@0.5"
+@end example
+
+@section drawtext
+
+Draw text string or text from specified file on top of video using the
+libfreetype library.
+
+To enable compilation of this filter you need to configure Libav with
+@code{--enable-libfreetype}.
+
+The filter also recognizes strftime() sequences in the provided text
+and expands them accordingly. Check the documentation of strftime().
+
+The filter accepts parameters as a list of @var{key}=@var{value} pairs,
+separated by ":".
+
+The description of the accepted parameters follows.
+
+@table @option
+
+@item fontfile
+The font file to be used for drawing text. Path must be included.
+This parameter is mandatory.
+
+@item text
+The text string to be drawn. The text must be a sequence of UTF-8
+encoded characters.
+This parameter is mandatory if no file is specified with the parameter
+@var{textfile}.
+
+@item textfile
+A text file containing text to be drawn. The text must be a sequence
+of UTF-8 encoded characters.
+
+This parameter is mandatory if no text string is specified with the
+parameter @var{text}.
+
+If both text and textfile are specified, an error is thrown.
+
+@item x, y
+The offsets where text will be drawn within the video frame.
+Relative to the top/left border of the output image.
+They accept expressions similar to the @ref{overlay} filter:
+@table @option
+
+@item x, y
+the computed values for @var{x} and @var{y}. They are evaluated for
+each new frame.
+
+@item main_w, main_h
+main input width and height
+
+@item W, H
+same as @var{main_w} and @var{main_h}
+
+@item text_w, text_h
+rendered text width and height
+
+@item w, h
+same as @var{text_w} and @var{text_h}
+
+@item n
+the number of frames processed, starting from 0
+
+@item t
+timestamp expressed in seconds, NAN if the input timestamp is unknown
+
+@end table
+
+The default value of @var{x} and @var{y} is 0.
+
+@item fontsize
+The font size to be used for drawing text.
+The default value of @var{fontsize} is 16.
+
+@item fontcolor
+The color to be used for drawing fonts.
+Either a string (e.g. "red") or in 0xRRGGBB[AA] format
+(e.g. "0xff000033"), possibly followed by an alpha specifier.
+The default value of @var{fontcolor} is "black".
+
+@item boxcolor
+The color to be used for drawing box around text.
+Either a string (e.g. "yellow") or in 0xRRGGBB[AA] format
+(e.g. "0xff00ff"), possibly followed by an alpha specifier.
+The default value of @var{boxcolor} is "white".
+
+@item box
+Used to draw a box around text using background color.
+Value should be either 1 (enable) or 0 (disable).
+The default value of @var{box} is 0.
+
+@item shadowx, shadowy
+The x and y offsets for the text shadow position with respect to the
+position of the text. They can be either positive or negative
+values. Default value for both is "0".
+
+@item shadowcolor
+The color to be used for drawing a shadow behind the drawn text. It
+can be a color name (e.g. "yellow") or a string in the 0xRRGGBB[AA]
+form (e.g. "0xff00ff"), possibly followed by an alpha specifier.
+The default value of @var{shadowcolor} is "black".
+
+@item ft_load_flags
+Flags to be used for loading the fonts.
+
+The flags map the corresponding flags supported by libfreetype, and are
+a combination of the following values:
+@table @var
+@item default
+@item no_scale
+@item no_hinting
+@item render
+@item no_bitmap
+@item vertical_layout
+@item force_autohint
+@item crop_bitmap
+@item pedantic
+@item ignore_global_advance_width
+@item no_recurse
+@item ignore_transform
+@item monochrome
+@item linear_design
+@item no_autohint
+@item end table
+@end table
+
+Default value is "render".
+
+For more information consult the documentation for the FT_LOAD_*
+libfreetype flags.
+
+@item tabsize
+The size in number of spaces to use for rendering the tab.
+Default value is 4.
+
+@item fix_bounds
+If true, check and fix text coords to avoid clipping.
+@end table
+
+For example the command:
+@example
+drawtext="fontfile=/usr/share/fonts/truetype/freefont/FreeSerif.ttf: text='Test Text'"
+@end example
+
+will draw "Test Text" with font FreeSerif, using the default values
+for the optional parameters.
+
+The command:
+@example
+drawtext="fontfile=/usr/share/fonts/truetype/freefont/FreeSerif.ttf: text='Test Text':\
+ x=100: y=50: fontsize=24: fontcolor=yellow@@0.2: box=1: boxcolor=red@@0.2"
+@end example
+
+will draw 'Test Text' with font FreeSerif of size 24 at position x=100
+and y=50 (counting from the top-left corner of the screen), text is
+yellow with a red box around it. Both the text and the box have an
+opacity of 20%.
+
+Note that the double quotes are not necessary if spaces are not used
+within the parameter list.
+
+For more information about libfreetype, check:
+@url{http://www.freetype.org/}.
+
+@section fade
+
+Apply fade-in/out effect to input video.
+
+It accepts the parameters:
+@var{type}:@var{start_frame}:@var{nb_frames}
+
+@var{type} specifies if the effect type, can be either "in" for
+fade-in, or "out" for a fade-out effect.
+
+@var{start_frame} specifies the number of the start frame for starting
+to apply the fade effect.
+
+@var{nb_frames} specifies the number of frames for which the fade
+effect has to last. At the end of the fade-in effect the output video
+will have the same intensity as the input video, at the end of the
+fade-out transition the output video will be completely black.
+
+A few usage examples follow, usable too as test scenarios.
+@example
+# fade in first 30 frames of video
+fade=in:0:30
+
+# fade out last 45 frames of a 200-frame video
+fade=out:155:45
+
+# fade in first 25 frames and fade out last 25 frames of a 1000-frame video
+fade=in:0:25, fade=out:975:25
+
+# make first 5 frames black, then fade in from frame 5-24
+fade=in:5:20
+@end example
+
+@section fieldorder
+
+Transform the field order of the input video.
+
+It accepts one parameter which specifies the required field order that
+the input interlaced video will be transformed to. The parameter can
+assume one of the following values:
+
+@table @option
+@item 0 or bff
+output bottom field first
+@item 1 or tff
+output top field first
+@end table
+
+Default value is "tff".
+
+Transformation is achieved by shifting the picture content up or down
+by one line, and filling the remaining line with appropriate picture content.
+This method is consistent with most broadcast field order converters.
+
+If the input video is not flagged as being interlaced, or it is already
+flagged as being of the required output field order then this filter does
+not alter the incoming video.
+
+This filter is very useful when converting to or from PAL DV material,
+which is bottom field first.
+
+For example:
@example
-# draw a black box around the edge of the input image
-drawbox
-
-# draw a box with color red and an opacity of 50%
-drawbox=10:20:200:60:red@@0.5"
+./avconv -i in.vob -vf "fieldorder=bff" out.dv
@end example
@section fifo
format=yuv420p:yuv444p:yuv410p
@end example
+@section fps
+
+Convert the video to specified constant framerate by duplicating or dropping
+frames as necessary.
+
+This filter accepts the following named parameters:
+@table @option
+
+@item fps
+Desired output framerate.
+
+@end table
+
@anchor{frei0r}
@section frei0r
Apply a frei0r effect to the input video.
To enable compilation of this filter you need to install the frei0r
-header and configure FFmpeg with --enable-frei0r.
+header and configure Libav with --enable-frei0r.
The filter supports the syntax:
@example
Interpolate the gradients that should go where the bands are, and
dither them.
+This filter is designed for playback only. Do not use it prior to
+lossy compression, because compression tends to lose the dither and
+bring back the bands.
+
The filter takes two optional parameters, separated by ':':
@var{strength}:@var{radius}
Flip the input video horizontally.
-For example to horizontally flip the video in input with
-@file{ffmpeg}:
+For example to horizontally flip the input video with @command{avconv}:
@example
-ffmpeg -i in.avi -vf "hflip" out.avi
+avconv -i in.avi -vf "hflip" out.avi
@end example
@section hqdn3d
@var{luma_tmp}*@var{chroma_spatial}/@var{luma_spatial}
@end table
-@section noformat
+@section lut, lutrgb, lutyuv
+
+Compute a look-up table for binding each pixel component input value
+to an output value, and apply it to input video.
+
+@var{lutyuv} applies a lookup table to a YUV input video, @var{lutrgb}
+to an RGB input video.
+
+These filters accept in input a ":"-separated list of options, which
+specify the expressions used for computing the lookup table for the
+corresponding pixel component values.
+
+The @var{lut} filter requires either YUV or RGB pixel formats in
+input, and accepts the options:
+@table @option
+@item @var{c0} (first pixel component)
+@item @var{c1} (second pixel component)
+@item @var{c2} (third pixel component)
+@item @var{c3} (fourth pixel component, corresponds to the alpha component)
+@end table
+
+The exact component associated to each option depends on the format in
+input.
+
+The @var{lutrgb} filter requires RGB pixel formats in input, and
+accepts the options:
+@table @option
+@item @var{r} (red component)
+@item @var{g} (green component)
+@item @var{b} (blue component)
+@item @var{a} (alpha component)
+@end table
+
+The @var{lutyuv} filter requires YUV pixel formats in input, and
+accepts the options:
+@table @option
+@item @var{y} (Y/luminance component)
+@item @var{u} (U/Cb component)
+@item @var{v} (V/Cr component)
+@item @var{a} (alpha component)
+@end table
+
+The expressions can contain the following constants and functions:
+
+@table @option
+@item E, PI, PHI
+the corresponding mathematical approximated values for e
+(euler number), pi (greek PI), PHI (golden ratio)
+
+@item w, h
+the input width and height
+
+@item val
+input value for the pixel component
+
+@item clipval
+the input value clipped in the @var{minval}-@var{maxval} range
+
+@item maxval
+maximum value for the pixel component
+
+@item minval
+minimum value for the pixel component
+
+@item negval
+the negated value for the pixel component value clipped in the
+@var{minval}-@var{maxval} range , it corresponds to the expression
+"maxval-clipval+minval"
+
+@item clip(val)
+the computed value in @var{val} clipped in the
+@var{minval}-@var{maxval} range
+
+@item gammaval(gamma)
+the computed gamma correction value of the pixel component value
+clipped in the @var{minval}-@var{maxval} range, corresponds to the
+expression
+"pow((clipval-minval)/(maxval-minval)\,@var{gamma})*(maxval-minval)+minval"
+
+@end table
+
+All expressions default to "val".
+
+Some examples follow:
+@example
+# negate input video
+lutrgb="r=maxval+minval-val:g=maxval+minval-val:b=maxval+minval-val"
+lutyuv="y=maxval+minval-val:u=maxval+minval-val:v=maxval+minval-val"
+
+# the above is the same as
+lutrgb="r=negval:g=negval:b=negval"
+lutyuv="y=negval:u=negval:v=negval"
+
+# negate luminance
+lutyuv=negval
+
+# remove chroma components, turns the video into a graytone image
+lutyuv="u=128:v=128"
+
+# apply a luma burning effect
+lutyuv="y=2*val"
+
+# remove green and blue components
+lutrgb="g=0:b=0"
+
+# set a constant alpha channel value on input
+format=rgba,lutrgb=a="maxval-minval/2"
+
+# correct luminance gamma by a 0.5 factor
+lutyuv=y=gammaval(0.5)
+@end example
+
+@section negate
+
+Negate input video.
+
+This filter accepts an integer in input, if non-zero it negates the
+alpha component (if available). The default value in input is 0.
Force libavfilter not to use any of the specified pixel formats for the
input to the next filter.
Apply video transform using libopencv.
To enable this filter install libopencv library and headers and
-configure FFmpeg with --enable-libopencv.
+configure Libav with --enable-libopencv.
The filter takes the parameters: @var{filter_name}@{:=@}@var{filter_params}.
filter. If not specified the default values are assumed.
Refer to the official libopencv documentation for more precise
-informations:
+information:
@url{http://opencv.willowgarage.com/documentation/c/image_filtering.html}
Follows the list of supported libopencv filters.
@var{struct_el} represents a structuring element, and has the syntax:
@var{cols}x@var{rows}+@var{anchor_x}x@var{anchor_y}/@var{shape}
-@var{cols} and @var{rows} represent the number of colums and rows of
+@var{cols} and @var{rows} represent the number of columns and rows of
the structuring element, @var{anchor_x} and @var{anchor_y} the anchor
point, and @var{shape} the shape for the structuring element, and
can be one of the values "rect", "cross", "ellipse", "custom".
This filter corresponds to the libopencv function @code{cvErode}.
The filter accepts the parameters: @var{struct_el}:@var{nb_iterations},
-with the same meaning and use of those of the dilate filter
-(@pxref{dilate}).
+with the same syntax and semantics as the @ref{dilate} filter.
@subsection smooth
These parameters correspond to the parameters assigned to the
libopencv function @code{cvSmooth}.
+@anchor{overlay}
@section overlay
Overlay one video on top of another.
overlay=main_w-overlay_w-10:main_h-overlay_h-10
# insert a transparent PNG logo in the bottom left corner of the input
-movie=logo.png [logo];
-[in][logo] overlay=10:main_h-overlay_h-10 [out]
+avconv -i input -i logo -filter_complex 'overlay=10:main_h-overlay_h-10' output
# insert 2 different transparent PNG logos (second logo on bottom
# right corner):
-movie=logo1.png [logo1];
-movie=logo2.png [logo2];
-[in][logo1] overlay=10:H-h-10 [in+logo1];
-[in+logo1][logo2] overlay=W-w-10:H-h-10 [out]
+avconv -i input -i logo1 -i logo2 -filter_complex
+'overlay=10:H-h-10,overlay=W-w-10:H-h-10' output
# add a transparent color layer on top of the main video,
# WxH specifies the size of the main input to the overlay filter
color=red@.3:WxH [over]; [in][over] overlay [out]
@end example
-You can chain togheter more overlays but the efficiency of such
+You can chain together more overlays but the efficiency of such
approach is yet to be tested.
@section pad
It accepts the following parameters:
@var{width}:@var{height}:@var{x}:@var{y}:@var{color}.
+The parameters @var{width}, @var{height}, @var{x}, and @var{y} are
+expressions containing the following constants:
+
+@table @option
+@item E, PI, PHI
+the corresponding mathematical approximated values for e
+(euler number), pi (greek PI), phi (golden ratio)
+
+@item in_w, in_h
+the input video width and height
+
+@item iw, ih
+same as @var{in_w} and @var{in_h}
+
+@item out_w, out_h
+the output width and height, that is the size of the padded area as
+specified by the @var{width} and @var{height} expressions
+
+@item ow, oh
+same as @var{out_w} and @var{out_h}
+
+@item x, y
+x and y offsets as specified by the @var{x} and @var{y}
+expressions, or NAN if not yet specified
+
+@item a
+input display aspect ratio, same as @var{iw} / @var{ih}
+
+@item hsub, vsub
+horizontal and vertical chroma subsample values. For example for the
+pixel format "yuv422p" @var{hsub} is 2 and @var{vsub} is 1.
+@end table
+
Follows the description of the accepted parameters.
@table @option
value for @var{width} or @var{height} is 0, the corresponding input size
is used for the output.
+The @var{width} expression can reference the value set by the
+@var{height} expression, and vice versa.
+
The default value of @var{width} and @var{height} is 0.
@item x, y
Specify the offsets where to place the input image in the padded area
with respect to the top/left border of the output image.
+The @var{x} expression can reference the value set by the @var{y}
+expression, and vice versa.
+
The default value of @var{x} and @var{y} is 0.
@item color
@end table
-For example:
+Some examples follow:
@example
# Add paddings with color "violet" to the input video. Output video
# size is 640x480, the top-left corner of the input video is placed at
-# row 0, column 40.
+# column 0, row 40.
pad=640:480:0:40:violet
+
+# pad the input to get an output with dimensions increased bt 3/2,
+# and put the input video at the center of the padded area
+pad="3/2*iw:3/2*ih:(ow-iw)/2:(oh-ih)/2"
+
+# pad the input to get a squared output with size equal to the maximum
+# value between the input width and height, and put the input video at
+# the center of the padded area
+pad="max(iw\,ih):ow:(ow-iw)/2:(oh-ih)/2"
+
+# pad the input to get a final w/h ratio of 16:9
+pad="ih*16/9:ih:(ow-iw)/2:(oh-ih)/2"
+
+# double output size and put the input video in the bottom-right
+# corner of the output padded area
+pad="2*iw:2*ih:ow-iw:oh-ih"
@end example
@section pixdesctest
Scale the input video to @var{width}:@var{height} and/or convert the image format.
-For example the command:
+The parameters @var{width} and @var{height} are expressions containing
+the following constants:
-@example
-./ffmpeg -i in.avi -vf "scale=200:100" out.avi
-@end example
+@table @option
+@item E, PI, PHI
+the corresponding mathematical approximated values for e
+(euler number), pi (greek PI), phi (golden ratio)
+
+@item in_w, in_h
+the input width and height
-will scale the input video to a size of 200x100.
+@item iw, ih
+same as @var{in_w} and @var{in_h}
+
+@item out_w, out_h
+the output (cropped) width and height
+
+@item ow, oh
+same as @var{out_w} and @var{out_h}
+
+@item dar, a
+input display aspect ratio, same as @var{iw} / @var{ih}
+
+@item sar
+input sample aspect ratio
+
+@item hsub, vsub
+horizontal and vertical chroma subsample values. For example for the
+pixel format "yuv422p" @var{hsub} is 2 and @var{vsub} is 1.
+@end table
If the input image format is different from the format requested by
the next filter, the scale filter will convert the input to the
The default value of @var{width} and @var{height} is 0.
+Some examples follow:
+@example
+# scale the input video to a size of 200x100.
+scale=200:100
+
+# scale the input to 2x
+scale=2*iw:2*ih
+# the above is the same as
+scale=2*in_w:2*in_h
+
+# scale the input to half size
+scale=iw/2:ih/2
+
+# increase the width, and set the height to the same size
+scale=3/2*iw:ow
+
+# seek for Greek harmony
+scale=iw:1/PHI*iw
+scale=ih*PHI:ih
+
+# increase the height, and set the width to 3/2 of the height
+scale=3/2*oh:3/5*ih
+
+# increase the size, but make the size a multiple of the chroma
+scale="trunc(3/2*iw/hsub)*hsub:trunc(3/2*ih/vsub)*vsub"
+
+# increase the width to a maximum of 500 pixels, keep the same input aspect ratio
+scale='min(500\, iw*3/2):-1'
+@end example
+
+@section select
+Select frames to pass in output.
+
+It accepts in input an expression, which is evaluated for each input
+frame. If the expression is evaluated to a non-zero value, the frame
+is selected and passed to the output, otherwise it is discarded.
+
+The expression can contain the following constants:
+
+@table @option
+@item PI
+Greek PI
+
+@item PHI
+golden ratio
+
+@item E
+Euler number
+
+@item n
+the sequential number of the filtered frame, starting from 0
+
+@item selected_n
+the sequential number of the selected frame, starting from 0
+
+@item prev_selected_n
+the sequential number of the last selected frame, NAN if undefined
+
+@item TB
+timebase of the input timestamps
+
+@item pts
+the PTS (Presentation TimeStamp) of the filtered video frame,
+expressed in @var{TB} units, NAN if undefined
+
+@item t
+the PTS (Presentation TimeStamp) of the filtered video frame,
+expressed in seconds, NAN if undefined
+
+@item prev_pts
+the PTS of the previously filtered video frame, NAN if undefined
+
+@item prev_selected_pts
+the PTS of the last previously filtered video frame, NAN if undefined
+
+@item prev_selected_t
+the PTS of the last previously selected video frame, NAN if undefined
+
+@item start_pts
+the PTS of the first video frame in the video, NAN if undefined
+
+@item start_t
+the time of the first video frame in the video, NAN if undefined
+
+@item pict_type
+the type of the filtered frame, can assume one of the following
+values:
+@table @option
+@item I
+@item P
+@item B
+@item S
+@item SI
+@item SP
+@item BI
+@end table
+
+@item interlace_type
+the frame interlace type, can assume one of the following values:
+@table @option
+@item PROGRESSIVE
+the frame is progressive (not interlaced)
+@item TOPFIRST
+the frame is top-field-first
+@item BOTTOMFIRST
+the frame is bottom-field-first
+@end table
+
+@item key
+1 if the filtered frame is a key-frame, 0 otherwise
+
+@item pos
+the position in the file of the filtered frame, -1 if the information
+is not available (e.g. for synthetic video)
+@end table
+
+The default value of the select expression is "1".
+
+Some examples follow:
+
+@example
+# select all frames in input
+select
+
+# the above is the same as:
+select=1
+
+# skip all frames:
+select=0
+
+# select only I-frames
+select='eq(pict_type\,I)'
+
+# select one frame every 100
+select='not(mod(n\,100))'
+
+# select only frames contained in the 10-20 time interval
+select='gte(t\,10)*lte(t\,20)'
+
+# select only I frames contained in the 10-20 time interval
+select='gte(t\,10)*lte(t\,20)*eq(pict_type\,I)'
+
+# select frames with a minimum distance of 10 seconds
+select='isnan(prev_selected_t)+gte(t-prev_selected_t\,10)'
+@end example
+
+@anchor{setdar}
+@section setdar
+
+Set the Display Aspect Ratio for the filter output video.
+
+This is done by changing the specified Sample (aka Pixel) Aspect
+Ratio, according to the following equation:
+@math{DAR = HORIZONTAL_RESOLUTION / VERTICAL_RESOLUTION * SAR}
+
+Keep in mind that this filter does not modify the pixel dimensions of
+the video frame. Also the display aspect ratio set by this filter may
+be changed by later filters in the filterchain, e.g. in case of
+scaling or if another "setdar" or a "setsar" filter is applied.
+
+The filter accepts a parameter string which represents the wanted
+display aspect ratio.
+The parameter can be a floating point number string, or an expression
+of the form @var{num}:@var{den}, where @var{num} and @var{den} are the
+numerator and denominator of the aspect ratio.
+If the parameter is not specified, it is assumed the value "0:1".
+
+For example to change the display aspect ratio to 16:9, specify:
+@example
+setdar=16:9
+# the above is equivalent to
+setdar=1.77777
+@end example
+
+See also the @ref{setsar} filter documentation.
+
@section setpts
Change the PTS (presentation timestamp) of the input video frames.
@item PREV_OUTPTS
previous output PTS
+@item RTCTIME
+wallclock (RTC) time in microseconds
+
+@item RTCSTART
+wallclock (RTC) time at the start of the movie in microseconds
+
@end table
Some examples follow:
# fixed rate 25 fps with some jitter
setpts='1/(25*TB) * (N + 0.05 * sin(N*2*PI/25))'
+
+# generate timestamps from a "live source" and rebase onto the current timebase
+setpts='(RTCTIME - RTCSTART) / (TB * 1000000)"
+@end example
+
+@anchor{setsar}
+@section setsar
+
+Set the Sample (aka Pixel) Aspect Ratio for the filter output video.
+
+Note that as a consequence of the application of this filter, the
+output display aspect ratio will change according to the following
+equation:
+@math{DAR = HORIZONTAL_RESOLUTION / VERTICAL_RESOLUTION * SAR}
+
+Keep in mind that the sample aspect ratio set by this filter may be
+changed by later filters in the filterchain, e.g. if another "setsar"
+or a "setdar" filter is applied.
+
+The filter accepts a parameter string which represents the wanted
+sample aspect ratio.
+The parameter can be a floating point number string, or an expression
+of the form @var{num}:@var{den}, where @var{num} and @var{den} are the
+numerator and denominator of the aspect ratio.
+If the parameter is not specified, it is assumed the value "0:1".
+
+For example to change the sample aspect ratio to 10:11, specify:
+@example
+setsar=10:11
@end example
@section settb
settb=AVTB
@end example
-@section slicify
+@section showinfo
-Pass the images of input video on to next video filter as multiple
-slices.
+Show a line containing various information for each input video frame.
+The input video is not modified.
-@example
-./ffmpeg -i in.avi -vf "slicify=32" out.avi
-@end example
+The shown line contains a sequence of key/value pairs of the form
+@var{key}:@var{value}.
+
+A description of each shown parameter follows:
+
+@table @option
+@item n
+sequential number of the input frame, starting from 0
+
+@item pts
+Presentation TimeStamp of the input frame, expressed as a number of
+time base units. The time base unit depends on the filter input pad.
+
+@item pts_time
+Presentation TimeStamp of the input frame, expressed as a number of
+seconds
+
+@item pos
+position of the frame in the input stream, -1 if this information in
+unavailable and/or meaningless (for example in case of synthetic video)
+
+@item fmt
+pixel format name
+
+@item sar
+sample aspect ratio of the input frame, expressed in the form
+@var{num}/@var{den}
+
+@item s
+size of the input frame, expressed in the form
+@var{width}x@var{height}
+
+@item i
+interlaced mode ("P" for "progressive", "T" for top field first, "B"
+for bottom field first)
+
+@item iskey
+1 if the frame is a key frame, 0 otherwise
+
+@item type
+picture type of the input frame ("I" for an I-frame, "P" for a
+P-frame, "B" for a B-frame, "?" for unknown type).
+Check also the documentation of the @code{AVPictureType} enum and of
+the @code{av_get_picture_type_char} function defined in
+@file{libavutil/avutil.h}.
+
+@item checksum
+Adler-32 checksum of all the planes of the input frame
+
+@item plane_checksum
+Adler-32 checksum of each plane of the input frame, expressed in the form
+"[@var{c0} @var{c1} @var{c2} @var{c3}]"
+@end table
+
+@section split
-The filter accepts the slice height as parameter. If the parameter is
-not specified it will use the default value of 16.
+Split input video into several identical outputs.
-Adding this in the beginning of filter chains should make filtering
-faster due to better use of the memory cache.
+The filter accepts a single parameter which specifies the number of outputs. If
+unspecified, it defaults to 2.
+
+For example
+@example
+avconv -i INPUT -filter_complex split=5 OUTPUT
+@end example
+will create 5 copies of the input video.
@section transpose
Negative values for the amount will blur the input video, while positive
values will sharpen. All parameters are optional and default to the
-equivalent of the string '5:5:1.0:0:0:0.0'.
+equivalent of the string '5:5:1.0:5:5:0.0'.
@table @option
@item chroma_msize_x
Set the chroma matrix horizontal size. It can be an integer between 3
-and 13, default value is 0.
+and 13, default value is 5.
@item chroma_msize_y
Set the chroma matrix vertical size. It can be an integer between 3
-and 13, default value is 0.
+and 13, default value is 5.
@item luma_amount
Set the chroma effect strength. It can be a float number between -2.0
# Strong blur of both luma and chroma parameters
unsharp=7:7:-2:7:7:-2
-# Use the default values with @command{ffmpeg}
-./ffmpeg -i in.avi -vf "unsharp" out.mp4
+# Use the default values with @command{avconv}
+./avconv -i in.avi -vf "unsharp" out.mp4
@end example
@section vflip
Flip the input video vertically.
@example
-./ffmpeg -i in.avi -vf "vflip" out.avi
+./avconv -i in.avi -vf "vflip" out.avi
@end example
@section yadif
Deinterlace the input video ("yadif" means "yet another deinterlacing
filter").
-It accepts the optional parameters: @var{mode}:@var{parity}.
+It accepts the optional parameters: @var{mode}:@var{parity}:@var{auto}.
@var{mode} specifies the interlacing mode to adopt, accepts one of the
following values:
@table @option
@item 0
-assume bottom field first
-@item 1
assume top field first
+@item 1
+assume bottom field first
@item -1
enable automatic detection
@end table
If interlacing is unknown or decoder does not export this information,
top field first will be assumed.
+@var{auto} specifies if deinterlacer should trust the interlaced flag
+and only deinterlace frames marked as interlaced
+
+@table @option
+@item 0
+deinterlace all frames
+@item 1
+only deinterlace frames marked as interlaced
+@end table
+
+Default value is 0.
+
@c man end VIDEO FILTERS
@chapter Video Sources
through the interface defined in @file{libavfilter/vsrc_buffer.h}.
It accepts the following parameters:
-@var{width}:@var{height}:@var{pix_fmt_string}:@var{timebase_num}:@var{timebase_den}
+@var{width}:@var{height}:@var{pix_fmt_string}:@var{timebase_num}:@var{timebase_den}:@var{sample_aspect_ratio_num}:@var{sample_aspect_ratio.den}
-All the parameters need to be explicitely defined.
+All the parameters need to be explicitly defined.
Follows the list of the accepted parameters.
@item timebase_num, timebase_den
Specify numerator and denomitor of the timebase assumed by the
timestamps of the buffered frames.
+
+@item sample_aspect_ratio.num, sample_aspect_ratio.den
+Specify numerator and denominator of the sample aspect ratio assumed
+by the video frames.
@end table
For example:
@example
-buffer=320:240:yuv410p:1:24
+buffer=320:240:yuv410p:1:24:1:1
@end example
will instruct the source to accept video frames with size 320x240 and
-with format "yuv410p" and assuming 1/24 as the timestamps timebase.
+with format "yuv410p", assuming 1/24 as the timestamps timebase and
+square pixels (1:1 sample aspect ratio).
Since the pixel format with name "yuv410p" corresponds to the number 6
-(check the enum PixelFormat definition in @file{libavutil/pixfmt.h}),
+(check the enum AVPixelFormat definition in @file{libavutil/pixfmt.h}),
this example corresponds to:
@example
buffer=320:240:6:1:24
@item frame_size
Specify the size of the sourced video, it may be a string of the form
-@var{width}x@var{heigth}, or the name of a size abbreviation. The
+@var{width}x@var{height}, or the name of a size abbreviation. The
default value is "320x240".
@item frame_rate
Read a video stream from a movie container.
+Note that this source is a hack that bypasses the standard input path. It can be
+useful in applications that do not support arbitrary filter graphs, but its use
+is discouraged in those that do. Specifically in @command{avconv} this filter
+should never be used, the @option{-filter_complex} option fully replaces it.
+
It accepts the syntax: @var{movie_name}[:@var{options}] where
@var{movie_name} is the name of the resource to read (not necessarily
a file but also a device or a stream accessed through some protocol),
Provide a frei0r source.
To enable compilation of this filter you need to install the frei0r
-header and configure FFmpeg with --enable-frei0r.
+header and configure Libav with --enable-frei0r.
The source supports the syntax:
@example
the form @var{num}/@var{den} or a frame rate abbreviation.
@var{src_name} is the name to the frei0r source to load. For more
information regarding frei0r and how to set the parameters read the
-section "frei0r" (@pxref{frei0r}) in the description of the video
-filters.
+section @ref{frei0r} in the description of the video filters.
Some examples follow:
@example
frei0r_src=200x200:10:partik0l=1234 [overlay]; [in][overlay] overlay
@end example
+@section rgbtestsrc, testsrc
+
+The @code{rgbtestsrc} source generates an RGB test pattern useful for
+detecting RGB vs BGR issues. You should see a red, green and blue
+stripe from top to bottom.
+
+The @code{testsrc} source generates a test video pattern, showing a
+color pattern, a scrolling gradient and a timestamp. This is mainly
+intended for testing purposes.
+
+Both sources accept an optional sequence of @var{key}=@var{value} pairs,
+separated by ":". The description of the accepted options follows.
+
+@table @option
+
+@item size, s
+Specify the size of the sourced video, it may be a string of the form
+@var{width}x@var{height}, or the name of a size abbreviation. The
+default value is "320x240".
+
+@item rate, r
+Specify the frame rate of the sourced video, as the number of frames
+generated per second. It has to be a string in the format
+@var{frame_rate_num}/@var{frame_rate_den}, an integer number, a float
+number or a valid video frame rate abbreviation. The default value is
+"25".
+
+@item sar
+Set the sample aspect ratio of the sourced video.
+
+@item duration
+Set the video duration of the sourced video. The accepted syntax is:
+@example
+[-]HH[:MM[:SS[.m...]]]
+[-]S+[.m...]
+@end example
+See also the function @code{av_parse_time()}.
+
+If not specified, or the expressed duration is negative, the video is
+supposed to be generated forever.
+@end table
+
+For example the following:
+@example
+testsrc=duration=5.3:size=qcif:rate=10
+@end example
+
+will generate a video with a duration of 5.3 seconds, with size
+176x144 and a framerate of 10 frames per second.
+
@c man end VIDEO SOURCES
@chapter Video Sinks
Below is a description of the currently available video sinks.
+@section buffersink
+
+Buffer video frames, and make them available to the end of the filter
+graph.
+
+This sink is intended for a programmatic use through the interface defined in
+@file{libavfilter/buffersink.h}.
+
@section nullsink
Null video sink, do absolutely nothing with the input video. It is
tools.
@c man end VIDEO SINKS
-
projects / ffmpeg / blobdiff